Overall width
Selected: 35.625 in. Earlier retained values: 36 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Overall width = 35 5/8"
View source scope, location, and impact on fitMeasurement evidence for Bosch B36CD10ENS
This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bosch B36CD10ENS
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Evidence summary
Complete mixed evidence
4exact-model manufacturer values
0verified equivalent/same-chassis values
11secondary-source-only values
1values with unresolved source details
Last reviewed: 2026-10-30. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Measurements and supporting evidence
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Conflicting sources — resolved | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf Overall width = 35 5/8"Open original source ↗ Why this value was usedOverall width = 35 5/8" Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69.5 in | ✓ Conflicting sources — resolved | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpointOpen original source ↗ Why this value was usedexact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70 in | ✓ Verified — retained secondary source | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf HxWxD) (inches) 70" x 36" x 25"Open original source ↗ Why this value was usedHxWxD) (inches) 70" x 36" x 25" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25 in | ✓ Verified — retained secondary source | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf Overall depth without doors and handles (inches) -> 25"Open original source ↗ Why this value was usedOverall depth without doors and handles (inches) -> 25" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.75 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Bosch | Page 1 | |
Value used by ExactFit28.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Current Bosch B36CD10ENS spec sheet (revision 9/26, PDF dated 2026-09-21, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf): page 1 'Overall depth with doors and handles 28 3/4"'; page 2 side views print 28 3/4 (731). The older 2/25 sheet's page 1 said 27 13/16" but its own page 2 drawing already printed 731 mm (28 3/4). Door handle type 'Integrated handle', so the closed depth without handles is the same 28 3/4 in.Open original source ↗ Why this value was usedCurrent Bosch B36CD10ENS spec sheet (revision 9/26, PDF dated 2026-09-21, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf): page 1 'Overall depth with doors and handles 28 3/4"'; page 2 side views print 28 3/4 (731). The older 2/25 sheet's page 1 said 27 13/16" but its own page 2 drawing already printed 731 mm (28 3/4). Door handle type 'Integrated handle', so the closed depth without handles is the same 28 3/4 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.75 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Bosch | Page 1 | |
Value used by ExactFit28.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Current Bosch B36CD10ENS spec sheet (revision 9/26, PDF dated 2026-09-21, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf): page 1 'Overall depth with doors and handles 28 3/4"'; page 2 side views print 28 3/4 (731). The older 2/25 sheet's page 1 said 27 13/16" but its own page 2 drawing already printed 731 mm (28 3/4).Open original source ↗ Why this value was usedCurrent Bosch B36CD10ENS spec sheet (revision 9/26, PDF dated 2026-09-21, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf): page 1 'Overall depth with doors and handles 28 3/4"'; page 2 side views print 28 3/4 (731). The older 2/25 sheet's page 1 said 27 13/16" but its own page 2 drawing already printed 731 mm (28 3/4). Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.375 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CD10ENS-93672158.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit43.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS-93672158.pdf Exact-model 90-degree plan directly prints rear-to-front open-door envelope 43 3/8 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model 90-degree plan directly prints rear-to-front open-door envelope 43 3/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf Required cutout size HxWxD = 70" x 36" x 25"Open original source ↗ Why this value was usedRequired cutout size HxWxD = 70" x 36" x 25" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36CD10ENS-93672158.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS-93672158.pdf Required cutout size directly prints height 70 in; do not add the separately stated 1/2-inch top ventilation gap.Open original source ↗ Why this value was usedRequired cutout size directly prints height 70 in; do not add the separately stated 1/2-inch top ventilation gap. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36CD10ENS-93672158.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS-93672158.pdf Required cutout size directly prints depth 25 in; do not replace it with case depth plus the rear gap.Open original source ↗ Why this value was usedRequired cutout size directly prints depth 25 in; do not replace it with case depth plus the rear gap. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | Bosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Bosch | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Current Bosch B36CD10ENS spec sheet (revision 9/26, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf), page 2 Installation Details, top view in the opening: 1/8 (3) printed at the left side and 1/8 (3) at the right side.Open original source ↗ Why this value was usedCurrent Bosch B36CD10ENS spec sheet (revision 9/26, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf), page 2 Installation Details, top view in the opening: 1/8 (3) printed at the left side and 1/8 (3) at the right side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | Bosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Bosch | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Current Bosch B36CD10ENS spec sheet (revision 9/26, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf), page 2 Installation Details, top view in the opening: 1/8 (3) printed at the left side and 1/8 (3) at the right side.Open original source ↗ Why this value was usedCurrent Bosch B36CD10ENS spec sheet (revision 9/26, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf), page 2 Installation Details, top view in the opening: 1/8 (3) printed at the left side and 1/8 (3) at the right side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.Open original source ↗ Why this value was usedExact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Bosch installation document — 93672158.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf Exact Bosch manual: leave 1 in behind for proper ventilation.Open original source ↗ Why this value was usedExact Bosch manual: leave 1 in behind for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.75 in | ? Verified — finalized database measurement | Bosch measurement source — 93672158.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit1.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 93672158.pdf Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 9.4375 in | ✓ Verified — exact model | Bosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Bosch | Page 2 | |
Value used by ExactFit9.4375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf Current Bosch B36CD10ENS spec sheet (revision 9/26), page 2 door-swing plan: 9 7/16 (239) from the cabinet side to the fully opened right door at 118°. Stored as the printed door projection past the cabinet side, as for B36CL84ENS (owner decision 2026-10-17).Open original source ↗ Why this value was usedCurrent Bosch B36CD10ENS spec sheet (revision 9/26), page 2 door-swing plan: 9 7/16 (239) from the cabinet side to the fully opened right door at 118°. Stored as the printed door projection past the cabinet side, as for B36CL84ENS (owner decision 2026-10-17). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Conflicting sources — resolved | Bosch installation document — 93672158.pdf assets.skulytics.io | Retained specification excerpt: Official sheet: Overall width = 35 5/8 in; 36 in is required cutout width. | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 93672158.pdf Official sheet: Overall width = 35 5/8 in; 36 in is required cutout width.Open original source ↗ Why this value was usedOfficial sheet: Overall width = 35 5/8 in; 36 in is required cutout width. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Conflicting published measurements
Cabinet height
Selected: 69.5 in. Earlier retained values: 70 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint
View source scope, location, and impact on fitDepth with door, without handles
Selected: 28.75 in. Earlier retained values: 25 in, 27.8125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current Bosch B36CD10ENS spec sheet (revision 9/26, PDF dated 2026-09-21, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf): page 1 'Overall depth with doors and handles 28 3/4"'; page 2 side views print 28 3/4 (731). The older 2/25 sheet's page 1 said 27 13/16" but its own page 2 drawing already printed 731 mm (28 3/4). Door handle type 'Integrated handle', so the closed depth without handles is the same 28 3/4 in.
View source scope, location, and impact on fitDepth with handle
Selected: 28.75 in. Earlier retained values: 25 in, 27.8125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current Bosch B36CD10ENS spec sheet (revision 9/26, PDF dated 2026-09-21, media3.bosch-home.com/Documents/25875147_B36CD10ENS_Spec_Sheet.pdf): page 1 'Overall depth with doors and handles 28 3/4"'; page 2 side views print 28 3/4 (731). The older 2/25 sheet's page 1 said 27 13/16" but its own page 2 drawing already printed 731 mm (28 3/4).
View source scope, location, and impact on fitMinimum cutout height
Selected: 70 in. Earlier retained values: 70.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Required cutout size directly prints height 70 in; do not add the separately stated 1/2-inch top ventilation gap.
View source scope, location, and impact on fitMinimum cutout depth
Selected: 25 in. Earlier retained values: 26 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Required cutout size directly prints depth 25 in; do not replace it with case depth plus the rear gap.
View source scope, location, and impact on fitCabinet case width
Selected: 35.625 in. Earlier retained values: 36 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Official sheet: Overall width = 35 5/8 in; 36 in is required cutout width.
View source scope, location, and impact on fitSource documents and pages
Bosch installation document — 93672158.pdf
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: B36CD10ENS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Bosch measurement source — B36CD10ENS_spec-sheet_2026-09.pdf
Bosch · Web source · exact model/source
Model numbers covered: B36CD10ENS. Publication/revision date: 9/26 (as printed on the document). Reviewed: 2026-10-30.
5 displayed measurements supported: Depth with door, without handles; Depth with handle; Left-side ventilation clearance; Right-side ventilation clearance; Wall clearance for fully open door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Bosch measurement source — B36CD10ENS-93672158.pdf
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B36CD10ENS. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
3 displayed measurements supported: Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Report a problem with this modelCheck whether B36CD10ENS fits your openingBack to Bosch B36CD10ENSRead the full verification methodology
Evidence reflects the sources reviewed on 2026-10-30. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.