This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Built-in
Market status: Reviewed (recorded 2026-08-17)
Last reviewed: 2026-09-24. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Conflicting sources — resolved | Bosch measurement source — installation-instructions.pdf Bosch | Page 19 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Width across the installed panels with the doors closed: 35 3/4 in; the case width is 35 1/4 in (owner decision 2026-09-24).Open original source ↗ Why this value was usedWidth across the installed panels with the doors closed: 35 3/4 in; the case width is 35 1/4 in (owner decision 2026-09-24). Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5625 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 20 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Minimum appliance/case height 83 9/16 inOpen original source ↗ Why this value was usedMinimum appliance/case height 83 9/16 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.5625 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 1 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Overall height 83 9/16 in Min. - 85 1/2 in Max.; canonical value is the documented adjustable minimumOpen original source ↗ Why this value was usedOverall height 83 9/16 in Min. - 85 1/2 in Max.; canonical value is the documented adjustable minimum Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 1 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Overall depth without doors and handles (inches) 24Open original source ↗ Why this value was usedOverall depth without doors and handles (inches) 24 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 21 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Product drawing depth without projecting handle 24 3/4 inOpen original source ↗ Why this value was usedProduct drawing depth without projecting handle 24 3/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.875 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 1 | |
Value used by ExactFit26.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Overall depth with doors and handles (inches) 26 7/8Open original source ↗ Why this value was usedOverall depth with doors and handles (inches) 26 7/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 45 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 21 | |
Value used by ExactFit45 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Proud-install case plane 24 in plus 21 in to front edge at 90 degreesOpen original source ↗ Why this value was usedProud-install case plane 24 in plus 21 in to front edge at 90 degrees Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.5 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 21 | |
Value used by ExactFit35.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Niche width 35 1/2-36 inOpen original source ↗ Why this value was usedNiche width 35 1/2-36 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 21 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Niche height 84 inOpen original source ↗ Why this value was usedNiche height 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 21 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Niche depth at least 24 inOpen original source ↗ Why this value was usedNiche depth at least 24 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 20 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Proud-install side gap range 1/8-3/8 in; minimum 1/8 inOpen original source ↗ Why this value was usedProud-install side gap range 1/8-3/8 in; minimum 1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 20 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Proud-install side gap range 1/8-3/8 in; minimum 1/8 inOpen original source ↗ Why this value was usedProud-install side gap range 1/8-3/8 in; minimum 1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 20 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Complete 84 in proud-install niche; no separately additive top gapOpen original source ↗ Why this value was usedComplete 84 in proud-install niche; no separately additive top gap Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0 in | ✓ Verified — exact model | Bosch measurement source — installation-instructions.pdf Bosch | Page 20 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf At least 24 in niche depth equals 24 in case depth; no separately additive rear gapOpen original source ↗ Why this value was usedAt least 24 in niche depth equals 24 in case depth; no separately additive rear gap Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.75 in | ? Verified — finalized database measurement | Bosch measurement source — installation-instructions.pdf Publisher not recorded | Page 20 | |
Value used by ExactFit3.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Installation instructions in this model's own folder: 3 3/4 in between the side of the appliance and an adjacent wall for the door to open 90 degrees. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedInstallation instructions in this model's own folder: 3 3/4 in between the side of the appliance and an adjacent wall for the door to open 90 degrees. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 10.625 in | ? Verified — finalized database measurement | Bosch measurement source — installation-instructions.pdf Publisher not recorded | Page 20 | |
Value used by ExactFit10.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — installation-instructions.pdf Installation instructions: 10 5/8 in for the door fully open. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedInstallation instructions: 10 5/8 in for the door fully open. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.25 in | ✓ Verified — exact model | Bosch measurement source — bosch-b36bt130ns.json Bosch | Page 1 | |
Value used by ExactFit35.25 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — bosch-b36bt130ns.json Overall width (inches) 35 1/4Open original source ↗ Why this value was usedOverall width (inches) 35 1/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 35.75 in. Earlier retained values: 35.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Width across the installed panels with the doors closed: 35 3/4 in; the case width is 35 1/4 in (owner decision 2026-09-24).
View source scope, location, and impact on fitPublisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-24.
10 displayed measurements supported: Overall width; Cabinet height; Depth with door, without handles; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Bosch · Web source · exact model/source
Model numbers covered: B36BT130NS. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
7 displayed measurements supported: Height with hinge / controlling height; Depth without door; Depth with handle; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-24. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.