Measurement evidence for Bosch B33CM10SNS

Value used by ExactFit

31.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall width = 31 1/4"

Why this value was used

Overall width = 31 1/4"

Other evidence found

• 33 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 33" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall height = 69 1/8"

Why this value was used

Overall height = 69 1/8"

Other evidence found

• 70 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 33" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall height = 69 1/8"

Why this value was used

Overall height = 69 1/8"

Other evidence found

• 70 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 33" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall depth without doors and handles (inches) -> 23 5/8"

Why this value was used

Overall depth without doors and handles (inches) -> 23 5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.1875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 103097921.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-29

Bosch B33CM10SNS spec sheet (6/25), page 2 Installation Details side view: 27 3/16 (691) from the back to the door front, between the 23 5/8 (600) case and the 28 1/4 (719) depth with handles in the top view. Page 1: 'Door handle type Bar handle'; its 'Overall depth without doors and handles 23 5/8"' is the case depth (already stored as depth_case_only_in).

Why this value was used

Bosch B33CM10SNS spec sheet (6/25), page 2 Installation Details side view: 27 3/16 (691) from the back to the door front, between the 23 5/8 (600) case and the 28 1/4 (719) depth with handles in the top view. Page 1: 'Door handle type Bar handle'; its 'Overall depth without doors and handles 23 5/8"' is the case depth (already stored as depth_case_only_in).

Other evidence found

• 25 in — superseded

  Document 103097921.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 33" x 25". The final reviewed registry supersedes this earlier audit value.

• 23.625 in — superseded

  Document 103097921.pdf; page 1. Model scope: not separately recorded. Raw value: Overall depth without doors and handles = 23 5/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall depth with doors and handles = 28 1/4"

Why this value was used

Overall depth with doors and handles = 28 1/4"

Other evidence found

• 25 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 33" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall depth with doors open 90° = 56"

Why this value was used

Overall depth with doors open 90° = 56"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Required cutout size H x W x D = 70" x 33" x 25"

Why this value was used

Required cutout size H x W x D = 70" x 33" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B33CM10SNS_103097921.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Required cutout size directly prints height 70 in; the separately stated 2-inch top ventilation instruction is not added again.

Why this value was used

Required cutout size directly prints height 70 in; the separately stated 2-inch top ventilation instruction is not added again.

Other evidence found

• 71.125 in — superseded

  Document 103097921.pdf; page 2. Model scope: not separately recorded. Raw value: 69 1/8 in appliance height plus documented 2 in top gap = 71 1/8 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B33CM10SNS_103097921.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Required cutout size directly prints depth 25 in; the separately stated 2-inch rear ventilation instruction is not added to the printed cutout.

Why this value was used

Required cutout size directly prints depth 25 in; the separately stated 2-inch rear ventilation instruction is not added to the printed cutout.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097920.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-05

Exact manual text requires at least 1 in from the sides to the wall.

Why this value was used

Exact manual text requires at least 1 in from the sides to the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097920.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-05

Exact manual text requires at least 1 in from the sides to the wall.

Why this value was used

Exact manual text requires at least 1 in from the sides to the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact manual: leave 2 in gap at the top and behind for proper ventilation.

Why this value was used

Exact manual: leave 2 in gap at the top and behind for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 103097921.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

2" (50) gap at the top and behind

Why this value was used

2" (50) gap at the top and behind

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Bosch measurement source — B33CM10SNS_103097921.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model reversible-door 90-degree plan directly prints a 2 7/8 in hinge-side door-use offset.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model reversible-door 90-degree plan directly prints a 2 7/8 in hinge-side door-use offset.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.25 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 103097921.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official sheet: Overall width = 31 1/4 in; 33 in is required cutout width.
Reviewed: 2026-09-04

Official sheet: Overall width = 31 1/4 in; 33 in is required cutout width.

Why this value was used

Official sheet: Overall width = 31 1/4 in; 33 in is required cutout width.

Other evidence found

• 33 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 33" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.