Measurement evidence for Bosch B30IB100SP

Value used by ExactFit

29.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 96878101.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall width = 29 3/4"

Why this value was used

Overall width = 29 3/4"

Other evidence found

• 30 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 84" x 30" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 96878101.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall height = 83 9/16" Min.

Why this value was used

Overall height = 83 9/16" Min.

Other evidence found

• 84 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 84" x 30" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 02ed30593610f5d34fb6f7a1604dafa8370c78a8031a850ea849d8b927a36e58.json
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Bosch page: overall appliance height 83 9/16 in; replaces a mismapped 85 1/2 in value.
Reviewed: 2026-09-05

Official Bosch page: overall appliance height 83 9/16 in; replaces a mismapped 85 1/2 in value.

Why this value was used

Official Bosch page: overall appliance height 83 9/16 in; replaces a mismapped 85 1/2 in value.

Other evidence found

• 84 in — superseded

  Document 96878101.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 84" x 30" x 25". The final reviewed registry supersedes this earlier audit value.

• 85.5 in — superseded

  Document 96878101.pdf; page 1. Model scope: not separately recorded. Raw value: Overall height = 85 1/2" Max.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 96878101.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall depth without doors and handles (inches) -> 24"

Why this value was used

Overall depth without doors and handles (inches) -> 24"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in = depth_case_only_in + 0.75

Confidence label: high.

Calculation inputs: Depth without door;

Primary evidence

Bosch measurement source — 96878101.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-24

Panel-ready appliance: cabinet depth 24 in (608 mm) plus a standard 3/4 in panel = 24 3/4 in. The sheet prints no depth with the panel; for a flush installation it requires a cutout at least 25 in (635 mm) deep.

Why this value was used

Panel-ready appliance: cabinet depth 24 in (608 mm) plus a standard 3/4 in panel = 24 3/4 in. The sheet prints no depth with the panel; for a flush installation it requires a cutout at least 25 in (635 mm) deep. Calculation or inference: depth_less_handles_in = depth_case_only_in + 0.75.

Other evidence found

• 25 in — superseded

  Document 96878101.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 84" x 30" x 25". The final reviewed registry supersedes this earlier audit value.

• 24 in — superseded

  Document 96878101.pdf; page 1. Model scope: not separately recorded. Raw value: exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 96878101.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

HxWxD) (inches) 84" x 30" x 25"

Why this value was used

HxWxD) (inches) 84" x 30" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

57 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25 + 32 = 57 in

Confidence label: high.

Primary evidence

Bosch measurement source — 96878101.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-14

The drawing measures the door at 90° from the cabinet (or case) front: 32" ; flush install: cabinet front at >= 25" (635 mm) from the back wall. Stored from the back, like every other model: 25 + 32 = 57 in (owner decision 2026-10-14). The printed 32" is the front-of-cabinet figure.

Why this value was used

The drawing measures the door at 90° from the cabinet (or case) front: 32" ; flush install: cabinet front at >= 25" (635 mm) from the back wall. Stored from the back, like every other model: 25 + 32 = 57 in (owner decision 2026-10-14). The printed 32" is the front-of-cabinet figure. Calculation or inference: 25 + 32 = 57 in.

Other evidence found

• 56.1811 in — superseded

  www.synergyhomeappliance.com; location not retained. Model scope: not separately recorded. Raw value: Two exact-model retailer specifications agree: Depth with open door 90 degree 1427 mm (56.1811 in).. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 32 in — superseded

  assets.skulytics.io; page 3. Model scope: not separately recorded. Raw value: Exact-model flush-install top view directly prints a 32 in rear-to-front envelope at the illustrated 90-degree door position.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 96878101.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Required cutout size HxWxD = 84" x 30" x 25"

Why this value was used

Required cutout size HxWxD = 84" x 30" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 02ed30593610f5d34fb6f7a1604dafa8370c78a8031a850ea849d8b927a36e58.json
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Bosch page: required cutout height 84 in.
Reviewed: 2026-09-05

Official Bosch page: required cutout height 84 in.

Why this value was used

Official Bosch page: required cutout height 84 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B30IB100SP-96878101.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Bosch summary directly prints required cutout size 84 x 30 x 25 in.

Why this value was used

Exact-model Bosch summary directly prints required cutout size 84 x 30 x 25 in.

Other evidence found

• 24 in — superseded

  Document 02ed30593610f5d34fb6f7a1604dafa8370c78a8031a850ea849d8b927a36e58.json; location not retained. Model scope: not separately recorded. Raw value: Official Bosch page: required cutout depth 24 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Bosch doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Bosch doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 84 - 83.5625

Confidence label: high.

Primary evidence

Bosch measurement source — B30IB100SP-96878101.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model sheet prints an 84 in required cutout height and 83 9/16 in minimum appliance height; exact minimum-setting residual is 7/16 in.

Why this value was used

Exact-model sheet prints an 84 in required cutout height and 83 9/16 in minimum appliance height; exact minimum-setting residual is 7/16 in. Calculation or inference: 84 - 83.5625.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25 - 24

Confidence label: high.

Primary evidence

Bosch measurement source — B30IB100SP-96878101.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model sheet prints a 25 in required flush cutout depth and 24 in appliance body depth without doors and handles; exact rear cavity residual is 1 in.

Why this value was used

Exact-model sheet prints a 25 in required flush cutout depth and 24 in appliance body depth without doors and handles; exact rear cavity residual is 1 in. Calculation or inference: 25 - 24.

Other evidence found

• 0 in — superseded

  Document 02ed30593610f5d34fb6f7a1604dafa8370c78a8031a850ea849d8b927a36e58.json; location not retained. Model scope: not separately recorded. Raw value: Panel-ready flush-install niche and appliance depths are both 24 in; no additional rear residual.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 96878101.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Door at 90 degrees: 1 in on the hinge side, for the flush installation the sheet depicts.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Door at 90 degrees: 1 in on the hinge side, for the flush installation the sheet depicts.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 96878101.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official sheet: Overall width = 29 3/4 in; 30 in is required cutout width.
Reviewed: 2026-09-04

Official sheet: Overall width = 29 3/4 in; 30 in is required cutout width.

Why this value was used

Official sheet: Overall width = 29 3/4 in; 30 in is required cutout width.

Other evidence found

• 30 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 84" x 30" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.