This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-27. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 23.625 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model Bosch sheet: Appliance dimensions (H x W x D) = 79 15/16 x 23 5/8 x 26 3/16 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Bosch sheet: Appliance dimensions (H x W x D) = 79 15/16 x 23 5/8 x 26 3/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 79.9375 in | ✓ Verified — retained secondary source | Bosch installation document — 74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit79.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 74542061.pdf Manufacturer appliance height is 79 15/16"; retailer case and hinge endpoints both report 79.93 inches.Open original source ↗ Why this value was usedManufacturer appliance height is 79 15/16"; retailer case and hinge endpoints both report 79.93 inches. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 79.9375 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit79.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model Bosch sheet directly prints appliance height 79 15/16 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Bosch sheet directly prints appliance height 79 15/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.625 in | ✓ Verified — retained secondary source | Bosch measurement source — 325607943 www.homedepot.com | Retained specification excerpt: B24 chassis exact specification: Depth (Less Door) 23.625 in; manufacturer drawing also prints 23 5/ | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 325607943 B24 chassis exact specification: Depth (Less Door) 23.625 in; manufacturer drawing also prints 23 5/8".Open original source ↗ Why this value was usedB24 chassis exact specification: Depth (Less Door) 23.625 in; manufacturer drawing also prints 23 5/8". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.1875 in | ✓ Verified — retained secondary source | Bosch measurement source — 325607943 www.homedepot.com | Retained specification excerpt: B24 chassis exact specification: Depth (Excluding Handles) 26.1875 in. | |
Value used by ExactFit26.1875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 325607943 B24 chassis exact specification: Depth (Excluding Handles) 26.1875 in.Open original source ↗ Why this value was usedB24 chassis exact specification: Depth (Excluding Handles) 26.1875 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.375 in | ✓ Conflicting sources — resolved | Bosch installation document — 74542061.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 74542061.pdf Manufacturer dimension drawing prints 28 3/8" handled depth and 26 3/16" depth excluding its recessed/bar handle.Open original source ↗ Why this value was usedManufacturer dimension drawing prints 28 3/8" handled depth and 26 3/16" depth excluding its recessed/bar handle. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.0625 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit48.0625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model Bosch plan views directly label the rear-to-open-door envelope 48 1/16 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Bosch plan views directly label the rear-to-open-door envelope 48 1/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 24 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model Bosch sheet: Required cutout size (H x W x D) = 80 7/16 x 24 x 24 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Bosch sheet: Required cutout size (H x W x D) = 80 7/16 x 24 x 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 80.4375 in | ✓ Verified — retained secondary source | Bosch measurement source — 74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit80.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 74542061.pdf cutout size (H x W x D) 80 7/16"Open original source ↗ Why this value was usedcutout size (H x W x D) 80 7/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — retained secondary source | Bosch specification record — 74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch specification record — 74542061.pdf Exact B24 chassis installation depth is 24 in.Open original source ↗ Why this value was usedExact B24 chassis installation depth is 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.1875 in | ✓ Verified — retained secondary source · Calculated/inferred | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (24 - 23.625) / 2 Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model sheet prints a 24 in opening and 23 5/8 in appliance width; centered per-side residual is exactly 3/16 in.Open original source ↗ Why this value was usedExact-model sheet prints a 24 in opening and 23 5/8 in appliance width; centered per-side residual is exactly 3/16 in. Calculation or inference: (24 - 23.625) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.1875 in | ✓ Verified — retained secondary source · Calculated/inferred | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (24 - 23.625) / 2 Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model sheet prints a 24 in opening and 23 5/8 in appliance width; centered per-side residual is exactly 3/16 in.Open original source ↗ Why this value was usedExact-model sheet prints a 24 in opening and 23 5/8 in appliance width; centered per-side residual is exactly 3/16 in. Calculation or inference: (24 - 23.625) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model Bosch installation elevation directly labels 1/2 in above the 79 15/16 in appliance.Open original source ↗ Why this value was usedExact-model Bosch installation elevation directly labels 1/2 in above the 79 15/16 in appliance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.375 in | ✓ Verified — retained secondary source · Calculated/inferred | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 - 23.625 Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model sheet prints a 24 in installation depth and 23 5/8 in cabinet/body depth; exact rear residual is 3/8 in.Open original source ↗ Why this value was usedExact-model sheet prints a 24 in installation depth and 23 5/8 in cabinet/body depth; exact rear residual is 3/8 in. Calculation or inference: 24 - 23.625. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.1875 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS_spec-sheet_2022-12.pdf static.pcrichard.com | Page 2 | |
Value used by ExactFit2.1875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS_spec-sheet_2022-12.pdf Exact-model Bosch B24CB50ESS spec sheet (12/22, Installation Details, hosted at static.pcrichard.com/docs/B24CB50ESS_Specifications-Sheet_01.pdf): beside a full wall the door opens to 90 degrees with 2 3/16 in (55 mm) between the case and the wall (25 13/16 in overall less the 23 5/8 in case). Beside a cabinet that ends at the front, the hinge side needs >= 13/16 in (20 mm) for the full 125-degree opening.Open original source ↗ Why this value was usedExact-model Bosch B24CB50ESS spec sheet (12/22, Installation Details, hosted at static.pcrichard.com/docs/B24CB50ESS_Specifications-Sheet_01.pdf): beside a full wall the door opens to 90 degrees with 2 3/16 in (55 mm) between the case and the wall (25 13/16 in overall less the 23 5/8 in case). Beside a cabinet that ends at the front, the hinge side needs >= 13/16 in (20 mm) for the full 125-degree opening. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 23.625 in | ✓ Verified — retained secondary source | Bosch measurement source — B24CB50ESS-74542061.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit23.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B24CB50ESS-74542061.pdf Exact-model Bosch sheet directly prints appliance width 23 5/8 in; the cabinet and closed door share this width endpoint.Open original source ↗ All retained supporting links
Why this value was usedExact-model Bosch sheet directly prints appliance width 23 5/8 in; the cabinet and closed door share this width endpoint. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 28.375 in. Earlier retained values: 26.1875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Manufacturer dimension drawing prints 28 3/8" handled depth and 26 3/16" depth excluding its recessed/bar handle.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B24CB50ESS. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
9 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with doors open at 90°; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Specification sheet · secondary model/source
Model numbers covered: B24CB50ESS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Cabinet height; Depth with handle; Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.homedepot.com · Web source · secondary model/source
Model numbers covered: B24CB50ESS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Depth without door; Depth with door, without handles.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗static.pcrichard.com · Web source · secondary model/source
Model numbers covered: B24CB50ESS. Publication/revision date: 12/22 (as printed on the document). Reviewed: 2026-10-27.
1 displayed measurements supported: Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-27. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.