Measurement evidence for Beko BFTF2716WHIM

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Beko BFTF2716WHIM fit check Check this model against your opening How ExactFit verifies measurements

Beko BFTF2716WHIM

Top Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

7exact-model manufacturer values

0verified equivalent/same-chassis values

7secondary-source-only values

2values with unresolved source details

Last reviewed: 2026-10-25. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	27.5625 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 3
Value used by ExactFit 27.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Cabinet width 27 9/16 in; no lateral door projection when closed Open original source ↗ Why this value was used Cabinet width 27 9/16 in; no lateral door projection when closed Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	67.1875 in	✓ Conflicting sources — resolved	Beko measurement source — 8700000595.pdf Beko	Page 3
Value used by ExactFit 67.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Height to top of cabinet 67 3/16 in Open original source ↗ Why this value was used Height to top of cabinet 67 3/16 in Other evidence found 27.5625 in — superseded Document 104280188.pdf; page 3. Model scope: not separately recorded. Raw value: Height to top of cabinet 279/16" (700 mm). The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	67.6875 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 3
Value used by ExactFit 67.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Overall height 67 11/16 in Open original source ↗ Why this value was used Overall height 67 11/16 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	23.625 in	✓ Conflicting sources — resolved	Beko measurement source — 104280190.pdf assets.skulytics.io	Page 3
Value used by ExactFit 23.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 104280190.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-13 Cabinet depth 21 5/8" (550 mm) with the note "Add 1 7/8" (48 mm) for bump outs on back"; the plan view prints 23 5/8" (600 mm). Case-only depth includes fixed rear spacers (owner Rule B). Open original source ↗ Why this value was used Cabinet depth 21 5/8" (550 mm) with the note "Add 1 7/8" (48 mm) for bump outs on back"; the plan view prints 23 5/8" (600 mm). Case-only depth includes fixed rear spacers (owner Rule B). Other evidence found 21.625 in — superseded Document 104280188.pdf; page 2. Model scope: not separately recorded. Raw value: Depth Without Doors 21 5/8. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	26.375 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280190.pdf assets.skulytics.io	Page 2
Value used by ExactFit 26.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidence Beko measurement source — 104280190.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Finish/ice-maker sibling propagation. Open original source ↗ Why this value was used Finish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	26.375 in	✓ Verified — retained secondary source	Beko installation document — 104280188.pdf assets.skulytics.io	Page 2
Value used by ExactFit 26.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko installation document — 104280188.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 H x W x D) (in) 67 11 11/16 16 x 27 9/16 16 x 26 3/8 Open original source ↗ Why this value was used H x W x D) (in) 67 11 11/16 16 x 27 9/16 16 x 26 3/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	51.75 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 3
Value used by ExactFit 51.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 90-degree door diagram total depth 51 3/4 in Open original source ↗ Why this value was used 90-degree door diagram total depth 51 3/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	31.5 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 4
Value used by ExactFit 31.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Installation opening width 31 1/2 in (800 mm) Open original source ↗ Why this value was used Installation opening width 31 1/2 in (800 mm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.9375 in	✓ Conflicting sources — resolved	Beko measurement source — 104280190.pdf assets.skulytics.io	Page 4
Value used by ExactFit 70.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 104280190.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-09 Cabinet installation drawing directly prints opening height 70 15/16 in. Open original source ↗ Why this value was used Cabinet installation drawing directly prints opening height 70 15/16 in. Other evidence found 71.625 in — superseded The same document as the value used above; page 4. Model scope: not separately recorded. Raw value: Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25.5625 in	✓ Verified — retained secondary source	Beko measurement source — 104280190.pdf linqcdn.avbportal.com	Page 4
Value used by ExactFit 25.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 104280190.pdf linqcdn.avbportal.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-09 Cabinet installation drawing directly prints opening depth 25 9/16 in. Open original source ↗ Why this value was used Cabinet installation drawing directly prints opening depth 25 9/16 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	2 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 4
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Open original source ↗ Why this value was used Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	2 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 4
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Open original source ↗ Why this value was used Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	3.9375 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280190.pdf assets.skulytics.io	Page 4
Value used by ExactFit 3.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Beko measurement source — 104280190.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances. Open original source ↗ Why this value was used Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances. Calculation or inference: cached documented shared chassis propagation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf linqcdn.avbportal.com	Page 4
Value used by ExactFit 2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFTF2716SS Confidence label: medium. Primary evidence Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf linqcdn.avbportal.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Conflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716SS; original evidence: 2"(50 mm) minimum clearance at rear Open original source ↗ Why this value was used Conflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716SS; original evidence: 2"(50 mm) minimum clearance at rear Calculation or inference: exact 8-dimension chassis signature; source model Beko BFTF2716SS. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	0.875 in	? Verified — finalized database measurement	Beko measurement source — 104280188.pdf Publisher not recorded	Page 3
Value used by ExactFit 0.875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 104280188.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-25 Exact-model Beko spec sheet, top view with the door open 90°: the door projects 7/8" (22.6 mm) beyond the cabinet side. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used Exact-model Beko spec sheet, top view with the door open 90°: the door projects 7/8" (22.6 mm) beyond the cabinet side. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	27.5625 in	✓ Verified — exact model	Beko measurement source — 8700000595.pdf Beko	Page 3
Value used by ExactFit 27.5625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — 8700000595.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Cabinet width 27 9/16 in Open original source ↗ Why this value was used Cabinet width 27 9/16 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 67.1875 in. Earlier retained values: 27.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Height to top of cabinet 67 3/16 in

View source scope, location, and impact on fit

Depth without door

Selected: 23.625 in. Earlier retained values: 21.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Cabinet depth 21 5/8" (550 mm) with the note "Add 1 7/8" (48 mm) for bump outs on back"; the plan view prints 23 5/8" (600 mm). Case-only depth includes fixed rear spacers (owner Rule B).

View source scope, location, and impact on fit

Minimum cutout height

Selected: 70.9375 in. Earlier retained values: 71.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Cabinet installation drawing directly prints opening height 70 15/16 in.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Beko measurement source — 8700000595.pdf

Beko · Web source · exact model/source

Model numbers covered: BFTF2716WHIM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with doors open at 90°; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Beko measurement source — 104280190.pdf

assets.skulytics.io · Web source · secondary model/source

Model numbers covered: BFTF2716WHIM. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

5 displayed measurements supported: Depth without door; Depth with door, without handles; Minimum cutout height; Minimum cutout depth; Top clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Beko measurement source — 104280188.pdf

Publisher not recorded · Retained document · Scope not established

Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-25.

2 displayed measurements supported: Depth with handle; Wall clearance for door open to 90°.

Availability: retained review record; original URL unavailable in the record.

Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf

linqcdn.avbportal.com · Web source · secondary model/source

Model numbers covered: BFTF2716WHIM. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

1 displayed measurements supported: Rear clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether BFTF2716WHIM fits your opening Back to Beko BFTF2716WHIM Read the full verification methodology

Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.

Evidence summary

Complete mixed evidence

Measurements and supporting evidence

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence