This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 27.5625 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit27.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Overall width. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.1875 in | ✓ Conflicting sources — resolved · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit67.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Cabinet height. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 67.6875 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit67.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Height with hinge / controlling height. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 21.625 in | ✓ Secondary source only | Beko BFTF2716SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SSIM Spec Sheet Depth Without Doors 21 5/8Open original source ↗ Why this value was usedDepth Without Doors 21 5/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.375 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Depth with door, without handles. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.375 in | ✓ Secondary source only | Beko BFTF2716SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SSIM Spec Sheet H x W x D) (in) 67 11 11/16 16 x 27 9/16 16 x 26 3/8Open original source ↗ Why this value was usedH x W x D) (in) 67 11 11/16 16 x 27 9/16 16 x 26 3/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 51.75 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit51.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 31.5 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Minimum cutout width. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.625 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit71.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceBeko BFTF2716SS Spec Sheet Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.Open original source ↗ Why this value was usedMinimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: max(height_case_in,height_hinge_in) + top_clearance_in. Measurement transferred: Minimum cutout height. Relevant equivalence evidence: Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.. Known differences: not separately recorded. Review decision: documented cavity formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 23.625 in | ✓ Secondary source only · Calculated/inferred | Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf linqcdn.avbportal.com | Page 4 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceBeko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf Minimum opening depth derived from case-only depth 21.625 in plus documented rear clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 21.625 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 2 in | ✓ Verified — exact model · Calculated/inferred | BFTF2716WH Beko | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFTF2716WH Confidence label: medium. Primary evidenceBFTF2716WH Conflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each sideOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFTF2716WH. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 2 in | ✓ Verified — exact model · Calculated/inferred | BFTF2716WH Beko | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFTF2716WH Confidence label: medium. Primary evidenceBFTF2716WH Conflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each sideOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFTF2716WH. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3.9375 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit3.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.Open original source ↗ Why this value was usedManufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances. Calculation or inference: cached documented shared chassis propagation. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.. Measurement transferred: Top clearance. Relevant equivalence evidence: Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.. Known differences: not separately recorded. Review decision: cached documented shared chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Secondary source only | Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf linqcdn.avbportal.com | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: full-page semantic adjudication of parser alternatives Confidence label: high. Primary evidenceBeko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf 2"(50 mm) minimum clearance at rearOpen original source ↗ Why this value was used2"(50 mm) minimum clearance at rear Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 2 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.Open original source ↗ Why this value was usedManufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances. Calculation or inference: cached documented shared chassis propagation. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.. Measurement transferred: Hinge-side wall clearance. Relevant equivalence evidence: Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.. Known differences: not separately recorded. Review decision: cached documented shared chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 27.5625 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit27.5625 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Cabinet case width. Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 2 in | ✓ Verified — equivalent model · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared current BFTF2716 chassis Confidence label: medium. Primary evidenceBeko BFTF2716SS Spec Sheet Finish/ice-maker sibling propagation.Open original source ↗ Why this value was usedFinish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis. Why evidence from BFTF2716SS appliesTarget model: BFTF2716SSIM. Supporting model: BFTF2716SS. Manufacturer: Beko. Product family and measurement relationship: shared current BFTF2716 chassis. Measurement transferred: Adjoining-wall clearance (reviewed endpoint). Relevant equivalence evidence: Finish/ice-maker sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 67.1875 in. Earlier retained values: 27.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Finish/ice-maker sibling propagation. Calculation or inference: shared current BFTF2716 chassis.
View source scope, location, and impact on fitassets.skulytics.io · Spec Sheet · equivalent model/source
Model numbers covered: BFTF2716SS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Top clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Spec Sheet · secondary model/source
Model numbers covered: BFTF2716SSIM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Depth without door; Depth with handle.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗linqcdn.avbportal.com · Web source · secondary model/source
Model numbers covered: BFTF2716SSIM. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Beko · Web source · exact model/source
Model numbers covered: BFTF2716SSIM. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.