This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 27.5625 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit27.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.1875 in | ✓ Conflicting sources — resolved | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit67.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 67.6875 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit67.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 21.625 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.375 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.375 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 51.75 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit51.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 31.5 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit31.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.625 in | ✓ Secondary source only · Calculated/inferred | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit71.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceBeko BFTF2716SS Spec Sheet Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.Open original source ↗ Why this value was usedMinimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 23.625 in | ✓ Secondary source only · Calculated/inferred | Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf linqcdn.avbportal.com | Page 4 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceBeko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf Minimum opening depth derived from case-only depth 21.625 in plus documented rear clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 21.625 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 2 in | ✓ Verified — exact model · Calculated/inferred | BFTF2716WH Beko | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFTF2716WH Confidence label: medium. Primary evidenceBFTF2716WH Conflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each sideOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFTF2716WH. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 2 in | ✓ Verified — exact model · Calculated/inferred | BFTF2716WH Beko | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFTF2716WH Confidence label: medium. Primary evidenceBFTF2716WH Conflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each sideOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFTF2716WH; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 2 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFTF2716WH. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3.9375 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit3.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.Open original source ↗ Why this value was usedManufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Secondary source only | Beko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf linqcdn.avbportal.com | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: full-page semantic adjudication of parser alternatives Confidence label: high. Primary evidenceBeko measurement source — 70f364aa61fe283ea6b9a3ab4dd7f16a9acb5d77eff9d3cb6cd5cfa6528b3799.pdf 2"(50 mm) minimum clearance at rearOpen original source ↗ Why this value was used2"(50 mm) minimum clearance at rear Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 2 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Manufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances.Open original source ↗ Why this value was usedManufacturer family sheet specifies 100 mm top and 50 mm rear/side installation clearances. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 27.5625 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit27.5625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 2 in | ✓ Secondary source only | Beko BFTF2716SS Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFTF2716SS Spec Sheet Current BFTF2716 chassis specification and installation drawings.Open original source ↗ Why this value was usedCurrent BFTF2716 chassis specification and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 67.1875 in. Earlier retained values: 27.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current BFTF2716 chassis specification and installation drawings.
View source scope, location, and impact on fitassets.skulytics.io · Spec Sheet · secondary model/source
Model numbers covered: BFTF2716SS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Top clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗linqcdn.avbportal.com · Web source · secondary model/source
Model numbers covered: BFTF2716SS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Beko · Web source · exact model/source
Model numbers covered: BFTF2716SS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.