Measurement evidence for Beko BFTF2715SSIM

Value used by ExactFit

27.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280215.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-04

Side view: 67 9/16" (1715.6 mm) to the top of the cabinet. The stored 67 3/16 is not printed.

Why this value was used

Side view: 67 9/16" (1715.6 mm) to the top of the cabinet. The stored 67 3/16 is not printed.

Other evidence found

• 67.75 in — superseded

  Document 104280215.pdf; page 1. Model scope: not separately recorded. Raw value: H x W x D 67 3/4 x 27 9/16 x 24 5/8 in. The final reviewed registry supersedes this earlier audit value.

• 67.1875 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Exact-model profile and 90-degree door drawing.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.5625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

• 24.625 in — superseded

  Document 104280215.pdf; page 1. Model scope: not separately recorded. Raw value: H x W x D 67 3/4 x 27 9/16 x 24 5/8 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

50.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.499508 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 27.5625 + 2 * 50/25.4 = 31.499508

Confidence label: high.

Primary evidence

Beko measurement source — Beko_BFTF2715SSIM_manual_2026-10-31.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-10-31

Beko BFTF2715SSIM manual p9: "at least 5 cm distance with the ceiling and side walls". Opening width = 27 9/16 + 5 cm + 5 cm = 31 1/2 in, the same as the 800 mm Beko prints for the BFTF2716 (same 700 mm chassis). Replaces 31 9/16 in, which rounded 5 cm up to 2 in.

Why this value was used

Beko BFTF2715SSIM manual p9: "at least 5 cm distance with the ceiling and side walls". Opening width = 27 9/16 + 5 cm + 5 cm = 31 1/2 in, the same as the 800 mm Beko prints for the BFTF2716 (same 700 mm chassis). Replaces 31 9/16 in, which rounded 5 cm up to 2 in. Calculation or inference: 27.5625 + 2 * 50/25.4 = 31.499508.

Other evidence found

• 29.5625 in — superseded

  Document 104280215.pdf; page 2. Model scope: not separately recorded. Raw value: Product width plus exact 1-in side clearance each side.. The final reviewed registry supersedes this earlier audit value.

• 31.5625 in — superseded

  The same document as the value used above; page 9. Model scope: not separately recorded. Raw value: Beko BFTF2715SSIM manual p9: "at least 5 cm distance with the ceiling and side walls" (stored as 2 in side clearance). Opening width = 27 9/16 + 2 + 2 = 31 9/16 in. The earlier figure used 1 in each side (Codex measurement review 2026-10-31).. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Beko measurement source — 104280216.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.

Why this value was used

Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Beko measurement source — 104280216.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Minimum opening depth is the verified cabinet depth plus the documented rear clearance.

Why this value was used

Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280216.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280216.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280216.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280216.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and side walls and uses the rear spacing wedge.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Beko measurement source — BFTF2715SSIM-104280215.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact 90-degree door drawing labels 1" (25.4 mm) hinge-side lateral clearance; this is distinct from the 2" ventilation clearance.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact 90-degree door drawing labels 1" (25.4 mm) hinge-side lateral clearance; this is distinct from the 2" ventilation clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.5625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280215.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model profile and 90-degree door drawing.

Why this value was used

Exact-model profile and 90-degree door drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.