Measurement evidence for Beko BFSB3622SS

Value used by ExactFit

35.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

• 8 in — superseded

  content.syndigo.com; location not retained. Model scope: not separately recorded. Raw value: 377/8" (962 mm) 41 (1057 4115/16" (1065 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 130° 130° 581/4" (1479 mm) 353/4" (908 mm) 375/16" (948 mm) 417/16" (1052 mm) 377/8" (962 mm) 415/8" (1057 mm) 4115/16" (1065 mm) 13/16" (20 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 90° 90° 130° 130° 4613/16" (1189 mm) 701/2" (1790.7 mm) overall height 69" (1752.6 mm) height to top of cabinet 235/8" (600 mm) cabinet depth 267/8" (682 mm) depth with door 287/8" (734 mm) depth with handle add 1" (25.4 mm) with front leveling feet fully extended add 1 3/4" (44 mm) for spacers on back 353/4" (908 mm) cabinet width 5" (127 mm) 4" (102 mm) electrical location 11" (280 mm) 2" (50.8 mm) 4" (102 mm) 1/4" (6 mm) water location (models with ice maker) 10" (254 mm) 2" (50.8 mm) 8 5 5 . 6 4 3 . [...] dimensions & weight product (h x w x d) (in) 70 1/2 2 x 35 3/4 x 28 7/8 height with hinge cap 70 1/2 height without hinge cap 69 depth with handles 28 7/8 depth without handles 26 7/8 depth with. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

• 8 in — superseded

  content.syndigo.com; location not retained. Model scope: not separately recorded. Raw value: 377/8" (962 mm) 41 (1057 4115/16" (1065 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 130° 130° 581/4" (1479 mm) 353/4" (908 mm) 375/16" (948 mm) 417/16" (1052 mm) 377/8" (962 mm) 415/8" (1057 mm) 4115/16" (1065 mm) 13/16" (20 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 90° 90° 130° 130° 4613/16" (1189 mm) 701/2" (1790.7 mm) overall height 69" (1752.6 mm) height to top of cabinet 235/8" (600 mm) cabinet depth 267/8" (682 mm) depth with door 287/8" (734 mm) depth with handle add 1" (25.4 mm) with front leveling feet fully extended add 1 3/4" (44 mm) for spacers on back 353/4" (908 mm) cabinet width 5" (127 mm) 4" (102 mm) electrical location 11" (280 mm) 2" (50.8 mm) 4" (102 mm) 1/4" (6 mm) water location (models with ice maker) 10" (254 mm) 2" (50.8 mm) 8 5 5 . 6 4 3 . [...] dimensions & weight product (h x w x d) (in) 70 1/2 2 x 35 3/4 x 28 7/8 height with hinge cap 70 1/2 height without hinge cap 69 depth with handles 28 7/8 depth without handles 26 7/8 depth with. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

• 8 in — superseded

  content.syndigo.com; location not retained. Model scope: not separately recorded. Raw value: 377/8" (962 mm) 41 (1057 4115/16" (1065 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 130° 130° 581/4" (1479 mm) 353/4" (908 mm) 375/16" (948 mm) 417/16" (1052 mm) 377/8" (962 mm) 415/8" (1057 mm) 4115/16" (1065 mm) 13/16" (20 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 90° 90° 130° 130° 4613/16" (1189 mm) 701/2" (1790.7 mm) overall height 69" (1752.6 mm) height to top of cabinet 235/8" (600 mm) cabinet depth 267/8" (682 mm) depth with door 287/8" (734 mm) depth with handle add 1" (25.4 mm) with front leveling feet fully extended add 1 3/4" (44 mm) for spacers on back 353/4" (908 mm) cabinet width 5" (127 mm) 4" (102 mm) electrical location 11" (280 mm) 2" (50.8 mm) 4" (102 mm) 1/4" (6 mm) water location (models with ice maker) 10" (254 mm) 2" (50.8 mm) 8 5 5 . 6 4 3 . [...] dimensions & weight product (h x w x d) (in) 70 1/2 2 x 35 3/4 x 28 7/8 height with hinge cap 70 1/2 height without hinge cap 69 depth with handles 28 7/8 depth without handles 26 7/8 depth with. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.8125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

• 8 in — superseded

  content.syndigo.com; location not retained. Model scope: not separately recorded. Raw value: 377/8" (962 mm) 41 (1057 4115/16" (1065 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 130° 130° 581/4" (1479 mm) 353/4" (908 mm) 375/16" (948 mm) 417/16" (1052 mm) 377/8" (962 mm) 415/8" (1057 mm) 4115/16" (1065 mm) 13/16" (20 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 90° 90° 130° 130° 4613/16" (1189 mm) 701/2" (1790.7 mm) overall height 69" (1752.6 mm) height to top of cabinet 235/8" (600 mm) cabinet depth 267/8" (682 mm) depth with door 287/8" (734 mm) depth with handle add 1" (25.4 mm) with front leveling feet fully extended add 1 3/4" (44 mm) for spacers on back 353/4" (908 mm) cabinet width 5" (127 mm) 4" (102 mm) electrical location 11" (280 mm) 2" (50.8 mm) 4" (102 mm) 1/4" (6 mm) water location (models with ice maker) 10" (254 mm) 2" (50.8 mm) 8 5 5 . 6 4 3 . [...] dimensions & weight product (h x w x d) (in) 70 1/2 2 x 35 3/4 x 28 7/8 height with hinge cap 70 1/2 height without hinge cap 69 depth with handles 28 7/8 depth without handles 26 7/8 depth with. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

• 8 in — superseded

  content.syndigo.com; location not retained. Model scope: not separately recorded. Raw value: 377/8" (962 mm) 41 (1057 4115/16" (1065 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 130° 130° 581/4" (1479 mm) 353/4" (908 mm) 375/16" (948 mm) 417/16" (1052 mm) 377/8" (962 mm) 415/8" (1057 mm) 4115/16" (1065 mm) 13/16" (20 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 90° 90° 130° 130° 4613/16" (1189 mm) 701/2" (1790.7 mm) overall height 69" (1752.6 mm) height to top of cabinet 235/8" (600 mm) cabinet depth 267/8" (682 mm) depth with door 287/8" (734 mm) depth with handle add 1" (25.4 mm) with front leveling feet fully extended add 1 3/4" (44 mm) for spacers on back 353/4" (908 mm) cabinet width 5" (127 mm) 4" (102 mm) electrical location 11" (280 mm) 2" (50.8 mm) 4" (102 mm) 1/4" (6 mm) water location (models with ice maker) 10" (254 mm) 2" (50.8 mm) 8 5 5 . 6 4 3 . [...] dimensions & weight product (h x w x d) (in) 70 1/2 2 x 35 3/4 x 28 7/8 height with hinge cap 70 1/2 height without hinge cap 69 depth with handles 28 7/8 depth without handles 26 7/8 depth with. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

39.749508 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.8125 + 2 * 50/25.4 = 39.749508

Confidence label: high.

Primary evidence

Beko measurement source — Beko_BFSB3622SS_manual_2026-10-31.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-10-31

Beko BFSB3622SS manual p10: in an alcove leave "at least 5 cm" to the ceiling and walls. Opening width = 35 13/16 + 5 cm + 5 cm = 39 3/4 in. Replaces 39 13/16 in, which rounded 5 cm up to 2 in.

Why this value was used

Beko BFSB3622SS manual p10: in an alcove leave "at least 5 cm" to the ceiling and walls. Opening width = 35 13/16 + 5 cm + 5 cm = 39 3/4 in. Replaces 39 13/16 in, which rounded 5 cm up to 2 in. Calculation or inference: 35.8125 + 2 * 50/25.4 = 39.749508.

Other evidence found

• 37.4375 in — superseded

  Document 104280156.pdf; page 2. Model scope: not separately recorded. Raw value: Closed width plus exact 13/16-in hinge clearance each side.. The final reviewed registry supersedes this earlier audit value.

• 39.8125 in — superseded

  The same document as the value used above; page 10. Model scope: not separately recorded. Raw value: Beko BFSB3622SS manual p10: in an alcove, leave "at least 5 cm" to the ceiling and walls (stored as 2 in side clearance). Opening width = 35 13/16 + 2 + 2 = 39 13/16 in. The earlier figure used the 13/16 in hinge clearance instead of the wall air gap (Codex measurement review 2026-10-31).. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Beko measurement source — 104280158.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.

Why this value was used

Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Beko measurement source — 104280158.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Minimum opening depth is the verified cabinet depth plus the documented rear clearance.

Why this value was used

Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280158.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280158.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280158.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104280158.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Why this value was used

Exact-model manufacturer manual requires approximately 2 in (5 cm) from ceiling and walls.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.8125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Beko measurement source — BFSB3622SS-104280156.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact 90-degree door drawing labels 13/16" (20 mm) hinge-side lateral clearance; this is distinct from the 2" ventilation clearance.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact 90-degree door drawing labels 13/16" (20 mm) hinge-side lateral clearance; this is distinct from the 2" ventilation clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.8125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104280156.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Why this value was used

Exact-model dimension drawing; maximum of unequal 90-degree door-depth envelopes used.

Other evidence found

• 8 in — superseded

  content.syndigo.com; location not retained. Model scope: not separately recorded. Raw value: 377/8" (962 mm) 41 (1057 4115/16" (1065 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 130° 130° 581/4" (1479 mm) 353/4" (908 mm) 375/16" (948 mm) 417/16" (1052 mm) 377/8" (962 mm) 415/8" (1057 mm) 4115/16" (1065 mm) 13/16" (20 mm) 247/16" (621 mm) 1215/16" (328 mm) 99/16" (243 mm) 90° 90° 130° 130° 4613/16" (1189 mm) 701/2" (1790.7 mm) overall height 69" (1752.6 mm) height to top of cabinet 235/8" (600 mm) cabinet depth 267/8" (682 mm) depth with door 287/8" (734 mm) depth with handle add 1" (25.4 mm) with front leveling feet fully extended add 1 3/4" (44 mm) for spacers on back 353/4" (908 mm) cabinet width 5" (127 mm) 4" (102 mm) electrical location 11" (280 mm) 2" (50.8 mm) 4" (102 mm) 1/4" (6 mm) water location (models with ice maker) 10" (254 mm) 2" (50.8 mm) 8 5 5 . 6 4 3 . [...] dimensions & weight product (h x w x d) (in) 70 1/2 2 x 35 3/4 x 28 7/8 height with hinge cap 70 1/2 height without hinge cap 69 depth with handles 28 7/8 depth without handles 26 7/8 depth with. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.