Cabinet height
Selected: 69 in. Earlier retained values: 69.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model product and installation drawings.
View source scope, location, and impact on fitMeasurement evidence for Beko BFFD3624XSS
This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Beko BFFD3624XSS
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Evidence summary
Complete mixed evidence
0exact-model manufacturer values
0verified equivalent/same-chassis values
14secondary-source-only values
2values with unresolved source details
Last reviewed: 2026-09-30. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Measurements and supporting evidence
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280154.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69 in | ✓ Conflicting sources — resolved | Beko installation document — 104280154.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit69 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280154.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25.5625 in | ✓ Conflicting sources — resolved | Beko measurement source — 104280154.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit25.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf Cabinet depth 23 5/8 in excluding the fixed rear spacers, which are 1 15/16 in; with them fitted the case-only depth is 25 9/16 in. Rule B: case-only depth includes fixed rear spacers.Open original source ↗ Why this value was usedCabinet depth 23 5/8 in excluding the fixed rear spacers, which are 1 15/16 in; with them fitted the case-only depth is 25 9/16 in. Rule B: case-only depth includes fixed rear spacers. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.75 in | ✓ Conflicting sources — resolved | Beko installation document — 104280154.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit26.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.875 in | ✓ Verified — retained secondary source | Beko installation document — 104280154.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 42.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280154.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit42.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 37 in | ✓ Conflicting sources — resolved | Beko installation document — 104280154.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit37 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.6875 in | ✓ Verified — retained secondary source | Beko measurement source — 104280154.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit71.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf Cabinet installation drawing directly prints opening height 71 11/16 in.Open original source ↗ Why this value was usedCabinet installation drawing directly prints opening height 71 11/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25.5625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280154.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit25.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf Cabinet installation drawing directly prints opening depth 25 9/16 in.Open original source ↗ Why this value was usedCabinet installation drawing directly prints opening depth 25 9/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280154.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280154.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280155.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280155.pdf Installation | Min Clearance From the Top: 2" inches | Min Clearance From the Sides: 5/8" inchesOpen original source ↗ Why this value was usedInstallation | Min Clearance From the Top: 2" inches | Min Clearance From the Sides: 5/8" inches Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.375 in | ✓ Verified — retained secondary source | Beko measurement source — 104280154.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit1.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf full-page adjudication=1.375; parser candidates=[1.625, 0.197]; 13/8" (35 mm) minimum clearance at rearOpen original source ↗ Why this value was usedfull-page adjudication=1.375; parser candidates=[1.625, 0.197]; 13/8" (35 mm) minimum clearance at rear Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3 in | ? Verified — finalized database measurement | Beko measurement source — 104280154.pdf Publisher not recorded | Page 3 | |
Value used by ExactFit3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280154.pdf 3 in beside the appliance for the fresh-food door to open 90 degrees. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used3 in beside the appliance for the fresh-food door to open 90 degrees. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280154.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280154.pdf Exact-model product and installation drawings.Open original source ↗ Why this value was usedExact-model product and installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Conflicting published measurements
Depth without door
Selected: 25.5625 in. Earlier retained values: 23.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Cabinet depth 23 5/8 in excluding the fixed rear spacers, which are 1 15/16 in; with them fitted the case-only depth is 25 9/16 in. Rule B: case-only depth includes fixed rear spacers.
View source scope, location, and impact on fitDepth with door, without handles
Selected: 26.75 in. Earlier retained values: 28.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model product and installation drawings.
View source scope, location, and impact on fitMinimum cutout width
Selected: 37 in. Earlier retained values: 36.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model product and installation drawings.
View source scope, location, and impact on fitMeasurements not established
Wall clearance for fully open door
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Source documents and pages
Beko installation document — 104280154.pdf
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: BFFD3624XSS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Beko measurement source — 104280155.pdf
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: BFFD3624XSS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Report a problem with this modelCheck whether BFFD3624XSS fits your openingBack to Beko BFFD3624XSSRead the full verification methodology
Evidence reflects the sources reviewed on 2026-09-30. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.