This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-25. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280124.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.375 in | ✓ Conflicting sources — resolved | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit67.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Product drawing: 67 3/8" (1711.5 mm) to the top of the cabinet; the user manual prints Height-Top Of Cabinet "B" 67 5/16" (1710 mm). The stored 69 7/8 in is the height with the hinge cap.Open original source ↗ Why this value was usedProduct drawing: 67 3/8" (1711.5 mm) to the top of the cabinet; the user manual prints Height-Top Of Cabinet "B" 67 5/16" (1710 mm). The stored 69 7/8 in is the height with the hinge cap. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.875 in | ✓ Verified — retained secondary source | Beko installation document — 104280124.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.625 in | ✓ Verified — retained secondary source | Beko installation document — 104280124.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 27.5625 in | ✓ Conflicting sources — resolved | Beko installation document — 104280124.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit27.5625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29.6875 in | ✓ Verified — retained secondary source | Beko installation document — 104280124.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.6875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 45.5625 in | ✓ Verified — retained secondary source | Beko installation document — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit45.5625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36.75 in | ✓ Conflicting sources — resolved | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit36.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Installation drawing directly prints opening width 36 3/4 in.Open original source ↗ Why this value was usedInstallation drawing directly prints opening width 36 3/4 in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72 in | ✓ Verified — retained secondary source | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Installation drawing directly prints opening height 72 in.Open original source ↗ Why this value was usedInstallation drawing directly prints opening height 72 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source · Calculated/inferred | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceBeko measurement source — 104280124.pdf Minimum opening depth derived from case-only depth 23.625 in plus documented rear clearance 1.375 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 23.625 in plus documented rear clearance 1.375 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.5625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.5625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Required Minimum Clearances: | Top: 2" | Sides: 9/16" on each sideOpen original source ↗ Why this value was usedRequired Minimum Clearances: | Top: 2" | Sides: 9/16" on each side Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.375 in | ✓ Verified — retained secondary source | Beko measurement source — 104280124.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit1.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Top: 2" | Sides: 9/16" on each side | Back: 1 3/8"Open original source ↗ Why this value was usedTop: 2" | Sides: 9/16" on each side | Back: 1 3/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.75 in | ? Verified — finalized database measurement | Beko measurement source — 104280124.pdf Publisher not recorded | Page 3 | |
Value used by ExactFit1.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280124.pdf Exact-model Beko spec sheet, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side (3" at 130°). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model Beko spec sheet, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side (3" at 130°). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280124.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280124.pdf Exact-model product and door-swing drawing.Open original source ↗ Why this value was usedExact-model product and door-swing drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 67.375 in. Earlier retained values: 69.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Product drawing: 67 3/8" (1711.5 mm) to the top of the cabinet; the user manual prints Height-Top Of Cabinet "B" 67 5/16" (1710 mm). The stored 69 7/8 in is the height with the hinge cap.
View source scope, location, and impact on fitSelected: 27.5625 in. Earlier retained values: 29.6875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model product and door-swing drawing.
View source scope, location, and impact on fitSelected: 36.75 in. Earlier retained values: 36.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Installation drawing directly prints opening width 36 3/4 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: BFFD3624SS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
16 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.