Measurement evidence for Beko BFBF3018SSIML

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Beko BFBF3018SSIML fit check Check this model against your opening How ExactFit verifies measurements

Beko BFBF3018SSIML

Bottom Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

0exact-model manufacturer values

0verified equivalent/same-chassis values

14secondary-source-only values

2values with unresolved source details

Last reviewed: 2026-10-25. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	29.125 in	✓ Verified — retained secondary source	Beko installation document — 104280274.pdf assets.skulytics.io	Page 2
Value used by ExactFit 29.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko installation document — 104280274.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4 Open original source ↗ Why this value was used H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	67.3125 in	✓ Conflicting sources — resolved · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 2
Value used by ExactFit 67.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared BFBF3018SSIM left/right chassis Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Hinge-side sibling propagation. Open original source ↗ Why this value was used Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis. Other evidence found 67.75 in — superseded Document 104280274.pdf; page 2. Model scope: not separately recorded. Raw value: H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	67.75 in	✓ Verified — retained secondary source	Beko installation document — 104280274.pdf assets.skulytics.io	Page 2
Value used by ExactFit 67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko installation document — 104280274.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4 Open original source ↗ Why this value was used H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	25.625 in	✓ Verified — retained secondary source	Beko installation document — 104280274.pdf (p.2) assets.skulytics.io	Page 2
Value used by ExactFit 25.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko installation document — 104280274.pdf (p.2) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth without Door (in) -> 25 5/8 Open original source ↗ Why this value was used Depth without Door (in) -> 25 5/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	28.25 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 2
Value used by ExactFit 28.25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared BFBF3018SSIM left/right chassis Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Hinge-side sibling propagation. Open original source ↗ Why this value was used Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	30.3125 in	✓ Conflicting sources — resolved · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 2
Value used by ExactFit 30.3125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared BFBF3018SSIM left/right chassis Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Hinge-side sibling propagation. Open original source ↗ Why this value was used Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis. Other evidence found 28.25 in — superseded Document 104280274.pdf; page 2. Model scope: not separately recorded. Raw value: H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	55.5 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 3
Value used by ExactFit 55.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared BFBF3018SSIM left/right chassis Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Hinge-side sibling propagation. Open original source ↗ Why this value was used Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	30.3125 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 2
Value used by ExactFit 30.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared BFBF3018SSIM left/right chassis Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Hinge-side sibling propagation. Open original source ↗ Why this value was used Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	69.75 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 4
Value used by ExactFit 69.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Open original source ↗ Why this value was used Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	26.375 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 4
Value used by ExactFit 26.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Open original source ↗ Why this value was used Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.5625 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 4
Value used by ExactFit 0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Cached manufacturer document specifies the installation clearances used for this model family. Open original source ↗ Why this value was used Cached manufacturer document specifies the installation clearances used for this model family. Calculation or inference: cached documented shared chassis propagation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.5625 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 4
Value used by ExactFit 0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Cached manufacturer document specifies the installation clearances used for this model family. Open original source ↗ Why this value was used Cached manufacturer document specifies the installation clearances used for this model family. Calculation or inference: cached documented shared chassis propagation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	2 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 4
Value used by ExactFit 2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Cached manufacturer document specifies the installation clearances used for this model family. Open original source ↗ Why this value was used Cached manufacturer document specifies the installation clearances used for this model family. Calculation or inference: cached documented shared chassis propagation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	0.75 in	✓ Verified — retained secondary source · Calculated/inferred	Beko measurement source — 104280256.pdf assets.skulytics.io	Page 4
Value used by ExactFit 0.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Beko measurement source — 104280256.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Cached manufacturer document specifies the installation clearances used for this model family. Open original source ↗ Why this value was used Cached manufacturer document specifies the installation clearances used for this model family. Calculation or inference: cached documented shared chassis propagation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	1.75 in	? Verified — finalized database measurement · Calculated/inferred	Beko measurement source — 104280274.pdf Publisher not recorded	Page 3
Value used by ExactFit 1.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 30.875 - 29.125 Confidence label: high. Primary evidence Beko measurement source — 104280274.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-25 Exact-model Beko spec sheet (left hinge), top view with the door open 90°: overall width 30 7/8" (784.2 mm) against a 29 1/8" (740 mm) cabinet; one door, so the extra width is on the hinge side. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used Exact-model Beko spec sheet (left hinge), top view with the door open 90°: overall width 30 7/8" (784.2 mm) against a 29 1/8" (740 mm) cabinet; one door, so the extra width is on the hinge side. Calculation or inference: 30.875 - 29.125. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	29.125 in	✓ Verified — retained secondary source	Beko installation document — 104280274.pdf assets.skulytics.io	Page 2
Value used by ExactFit 29.125 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko installation document — 104280274.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4 Open original source ↗ Why this value was used H x W x D (in) 67 3/4 x 29 1/8 x 28 1/4 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 67.3125 in. Earlier retained values: 67.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis.

View source scope, location, and impact on fit

Depth with handle

Selected: 30.3125 in. Earlier retained values: 28.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Hinge-side sibling propagation. Calculation or inference: shared BFBF3018SSIM left/right chassis.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Beko installation document — 104280274.pdf

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: BFBF3018SSIML. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

4 displayed measurements supported: Overall width; Height with hinge / controlling height; Wall clearance for door open to 90°; Cabinet case width.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Beko measurement source — 104280256.pdf

assets.skulytics.io · Web source · secondary model/source

Model numbers covered: BFBF3018SSIML. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

11 displayed measurements supported: Cabinet height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Beko installation document — 104280274.pdf (p.2)

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: BFBF3018SSIML. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

1 displayed measurements supported: Depth without door.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether BFBF3018SSIML fits your opening Back to Beko BFBF3018SSIML Read the full verification methodology

Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.

Evidence summary

Complete mixed evidence

Measurements and supporting evidence

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence