This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.125 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit29.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.3125 in | ✓ Conflicting sources — resolved | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit67.3125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 67.75 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25.625 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit25.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.25 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit28.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 30.3125 in | ✓ Conflicting sources — resolved | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit30.3125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 55.5 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit55.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | Unknown | ? Not found · Calculated/inferred | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: matching BFBF3018 installation opening Confidence label: medium. Primary evidenceBeko BFBF3018SSIM Spec Sheet Shared chassis installation opening.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 30.3125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.75 in | ✓ Secondary source only · Calculated/inferred | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceBeko BFBF3018SSIM Spec Sheet Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.Open original source ↗ Why this value was usedMinimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26.375 in | ✓ Secondary source only · Calculated/inferred | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit26.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceBeko BFBF3018SSIM Spec Sheet Minimum opening depth is the verified cabinet depth plus the documented rear clearance.Open original source ↗ Why this value was usedMinimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.5625 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit0.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.5625 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit0.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.75 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 4 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Cached manufacturer document specifies the installation clearances used for this model family.Open original source ↗ Why this value was usedCached manufacturer document specifies the installation clearances used for this model family. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 0.5625 in | ✓ Secondary source only · Calculated/inferred | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit0.5625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBF3018SSIML Confidence label: medium. Primary evidenceBeko BFBF3018SSIM Spec Sheet Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBF3018SSIML; original evidence: Legacy reviewed field migration; endpoint indicators=['hinge-side']; Hinge-side sibling propagation.Open original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFBF3018SSIML; original evidence: Legacy reviewed field migration; endpoint indicators=['hinge-side']; Hinge-side sibling propagation. Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBF3018SSIML. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.125 in | ✓ Secondary source only | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit29.125 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko BFBF3018SSIM Spec Sheet Exact ice-maker model drawing; shared-chassis installation envelope.Open original source ↗ Why this value was usedExact ice-maker model drawing; shared-chassis installation envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | Unknown | ? Not found · Calculated/inferred | Beko BFBF3018SSIM Spec Sheet assets.skulytics.io | Page 3 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: matching BFBF3018 installation clearance Confidence label: medium. Primary evidenceBeko BFBF3018SSIM Spec Sheet Shared chassis 9/16-in side clearance.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.5625 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 67.3125 in. Earlier retained values: 67.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact ice-maker model drawing; shared-chassis installation envelope.
View source scope, location, and impact on fitSelected: 30.3125 in. Earlier retained values: 28.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact ice-maker model drawing; shared-chassis installation envelope.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 104280256.pdf. Related-model record: BFBF3018SSIM.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 104280256.pdf. Related-model record: BFBF3018SSIM.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Spec Sheet · Scope not established
Model numbers covered: BFBF3018SSIM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
17 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.