Measurement evidence for Beko BFBF2815SS

Value used by ExactFit

27.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

• 24.5 in — superseded

  Document 104281003.pdf; page 3. Model scope: not separately recorded. Raw value: Aligned with case_width_in (24.5"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

• 27.5625 in — superseded

  Document 104281003.pdf; page 3. Model scope: not separately recorded. Raw value: Height to top of cabinet 279/16" (700 mm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104281003.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-04

Cabinet depth 21 5/8" (550 mm) with the note "Add 1 7/8" (48 mm) for bump outs on back"; the side view prints 23 9/16" (598 mm). Case-only depth includes fixed rear spacers (owner Rule B).

Why this value was used

Cabinet depth 21 5/8" (550 mm) with the note "Add 1 7/8" (48 mm) for bump outs on back"; the side view prints 23 9/16" (598 mm). Case-only depth includes fixed rear spacers (owner Rule B).

Other evidence found

• 21.625 in — superseded

  Document 104281003.pdf; page 2. Model scope: not separately recorded. Raw value: Depth Without Doors 21 5/8. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

24.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

51.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Beko measurement source — 2022-12-19-15-50-12.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 67.6875 in plus documented top clearance 2.0 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 67.6875 in plus documented top clearance 2.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Beko measurement source — 2022-12-19-15-50-12.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-04

Recalculated 2026-10-04 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 23.5625, rear_clearance_in = 1.375 = 24.9375 in (previously 23 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 23.5625, rear_clearance_in = 1.375 = 24.9375 in (previously 23 in). Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.562 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from BFBF2815SSIM

Confidence label: medium.

Primary evidence

Beko measurement source — 2022-12-19-15-50-12.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: side_ventilation_clearance_in=0.562 in.

Why this value was used

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: side_ventilation_clearance_in=0.562 in. Calculation or inference: identical 8-dimension chassis signature; propagated from BFBF2815SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.562 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from BFBF2815SSIM

Confidence label: medium.

Primary evidence

Beko measurement source — 2022-12-19-15-50-12.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: side_ventilation_clearance_in=0.562 in.

Why this value was used

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: side_ventilation_clearance_in=0.562 in. Calculation or inference: identical 8-dimension chassis signature; propagated from BFBF2815SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from BFBF2815SSIM

Confidence label: medium.

Primary evidence

Beko measurement source — 2022-12-19-15-50-12.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: top_clearance_in=2.0 in.

Why this value was used

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: top_clearance_in=2.0 in. Calculation or inference: identical 8-dimension chassis signature; propagated from BFBF2815SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from BFBF2815SSIM

Confidence label: medium.

Primary evidence

Beko measurement source — 2022-12-19-15-50-12.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: rear_clearance_in=1.375 in.

Why this value was used

Conflict-free identical-chassis propagation from Beko BFBF2815SSIM: rear_clearance_in=1.375 in. Calculation or inference: identical 8-dimension chassis signature; propagated from BFBF2815SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.9375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko measurement source — 104281003.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-25

Exact-model Beko spec sheet, top view with the door open 90°: the door projects 15/16" (24 mm) beyond the cabinet side.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Beko spec sheet, top view with the door open 90°: the door projects 15/16" (24 mm) beyond the cabinet side.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.5625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko installation document — 104281003.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

BFBF2815 exact chassis sheet and diagrams.

Why this value was used

BFBF2815 exact chassis sheet and diagrams.

Other evidence found

• 24.5 in — superseded

  Document 104281003.pdf; page 3. Model scope: not separately recorded. Raw value: Cabinet width 241/2" (622.7 mm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.