This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-25. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf 29 3/4"Open original source ↗ Why this value was used29 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.5 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit68.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf Height Without Hinge Cap: 68 1/2"Open original source ↗ Why this value was usedHeight Without Hinge Cap: 68 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.6875 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit69.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf Height With Hinge Cap: 69 11/16"Open original source ↗ Why this value was usedHeight With Hinge Cap: 69 11/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25.625 in | ✓ Conflicting sources — resolved | Beko measurement source — 104280914.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit25.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280914.pdf Depth with the fixed rear spacers fitted, doors and handles excluded: 25 5/8 in (rule B).Open original source ↗ Why this value was usedDepth with the fixed rear spacers fitted, doors and handles excluded: 25 5/8 in (rule B). Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 27.5625 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit27.5625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf Depth Without Handles: 27 9/16"Open original source ↗ Why this value was usedDepth Without Handles: 27 9/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29.8125 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.8125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf Depth With Handles: 29 13/16"Open original source ↗ Why this value was usedDepth With Handles: 29 13/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 55.25 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit55.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf Depth with door open 90°: 55 1/4" (1403 mm)Open original source ↗ Why this value was usedDepth with door open 90°: 55 1/4" (1403 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30.9375 in | ✓ Conflicting sources — resolved · Calculated/inferred | Beko measurement source — 104280914.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit30.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared BFBD30216 chassis Confidence label: medium. Primary evidenceBeko measurement source — 104280914.pdf Conflict-free ice-maker/hinge-side chassis propagation.Open original source ↗ Why this value was usedConflict-free ice-maker/hinge-side chassis propagation. Calculation or inference: shared BFBD30216 chassis. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280914.pdf applianceiq.ai | Page 4 | |
Value used by ExactFit71.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280914.pdf Cabinet installation drawing directly prints opening height 71 5/8 in.Open original source ↗ Why this value was usedCabinet installation drawing directly prints opening height 71 5/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25.5625 in | ✓ Verified — retained secondary source | Beko measurement source — 104280914.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit25.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280914.pdf Cabinet installation drawing directly prints opening/countertop depth 25 9/16 in.Open original source ↗ Why this value was usedCabinet installation drawing directly prints opening/countertop depth 25 9/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.5625 in | ✓ Verified — exact model · Calculated/inferred | Beko measurement source — en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko | Page 4 | |
Value used by ExactFit0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM Confidence label: medium. Primary evidenceBeko measurement source — en-US-8700000762-202304051742300-Product-Formen-US.pdf Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each sideOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.5625 in | ✓ Verified — exact model · Calculated/inferred | Beko measurement source — en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko | Page 4 | |
Value used by ExactFit0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM Confidence label: medium. Primary evidenceBeko measurement source — en-US-8700000762-202304051742300-Product-Formen-US.pdf Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each sideOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280914.pdf applianceiq.ai | Page 4 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280914.pdf Drawing directly requires 2 in minimum clearance above refrigerator and alcove.Open original source ↗ Why this value was usedDrawing directly requires 2 in minimum clearance above refrigerator and alcove. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.1875 in | ✓ Verified — retained secondary source | Beko measurement source — 104280914.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit1.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280914.pdf Top-view drawing directly requires 1 3/16 in minimum rear clearance.Open original source ↗ Why this value was usedTop-view drawing directly requires 1 3/16 in minimum rear clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.1875 in | ? Verified — finalized database measurement | Beko measurement source — 104280998.pdf Publisher not recorded | Page 3 | |
Value used by ExactFit3.1875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280998.pdf Exact-model Beko spec sheet, top view with the door open 90°: the door projects 3 3/16" (81 mm) beyond the cabinet side (left hinge). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model Beko spec sheet, top view with the door open 90°: the door projects 3 3/16" (81 mm) beyond the cabinet side (left hinge). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 20.1875 in | ? Verified — finalized database measurement | Beko measurement source — 104280914.pdf Publisher not recorded | Page 4 | |
Value used by ExactFit20.1875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280914.pdf Right-hinged door fully open to 130 degrees: 20 3/16 in between the side of the appliance and the wall. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedRight-hinged door fully open to 130 degrees: 20 3/16 in between the side of the appliance and the wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280998.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280998.pdf 29 3/4"Open original source ↗ Why this value was used29 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 25.625 in. Earlier retained values: 24.4375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Depth with the fixed rear spacers fitted, doors and handles excluded: 25 5/8 in (rule B).
View source scope, location, and impact on fitSelected: 30.9375 in. Earlier retained values: 30.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Conflict-free ice-maker/hinge-side chassis propagation. Calculation or inference: shared BFBD30216 chassis.
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: BFBD30216SSL. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-25.
7 displayed measurements supported: Depth without door; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Beko · Web source · exact model/source
Model numbers covered: BFBD30216SSL. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.