Measurement evidence for Beko BFBD30216SSIM

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Beko BFBD30216SSIM fit check Check this model against your opening How ExactFit verifies measurements

Beko BFBD30216SSIM

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

8exact-model manufacturer values

2verified equivalent/same-chassis values

6secondary-source-only values

0values with unresolved source details

Last reviewed: 2026-09-05. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	29.75 in	✓ Secondary source only	Beko BFBD30216SSIM Spec Sheet assets.skulytics.io	Page 2
Value used by ExactFit 29.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko BFBD30216SSIM Spec Sheet assets.skulytics.io · Spec Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 H x W x D) (in) 69 11 11/16 16 x 29 3/4 x 29 13 13/16 16 Open original source ↗ Why this value was used H x W x D) (in) 69 11 11/16 16 x 29 3/4 x 29 13 13/16 16 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.5 in	✓ Secondary source only	Beko BFBD30216SSIM Spec Sheet assets.skulytics.io	Page 2
Value used by ExactFit 68.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko BFBD30216SSIM Spec Sheet assets.skulytics.io · Spec Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Height Without Hinge Cap -> 68 1/2 Open original source ↗ Why this value was used Height Without Hinge Cap -> 68 1/2 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.6875 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 3
Value used by ExactFit 69.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Overall height 69 11/16 in Open original source ↗ Why this value was used Overall height 69 11/16 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24.4375 in	✓ Conflicting sources — resolved	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 3
Value used by ExactFit 24.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Cabinet depth 24 7/16 in Open original source ↗ Why this value was used Cabinet depth 24 7/16 in Other evidence found 25.5625 in — superseded 104280985.pdf; page 4. Model scope: not separately recorded. Raw value: Depth of cabinet 259/16" (650 mm). The final reviewed registry supersedes this earlier audit value. Cabinet depth 24 7/16 in Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	27.5625 in	✓ Conflicting sources — resolved	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 3
Value used by ExactFit 27.5625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Depth with door 27 9/16 in, excluding handle Open original source ↗ Why this value was used Depth with door 27 9/16 in, excluding handle Other evidence found 29.8125 in — superseded 104280985.pdf; page 3. Model scope: not separately recorded. Raw value: Depth with door 2913/16" (758 mm). The final reviewed registry supersedes this earlier audit value. Depth with door 27 9/16 in, excluding handle Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	29.8125 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 3
Value used by ExactFit 29.8125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Depth with handle 29 13/16 in Open original source ↗ Why this value was used Depth with handle 29 13/16 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	55.25 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 3
Value used by ExactFit 55.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 90-degree door diagram total depth 55 1/4 in Open original source ↗ Why this value was used 90-degree door diagram total depth 55 1/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	30.9375 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 4
Value used by ExactFit 30.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Installation opening width 30 15/16 in (786 mm) Open original source ↗ Why this value was used Installation opening width 30 15/16 in (786 mm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.6875 in	✓ Secondary source only · Calculated/inferred	Beko BFBD30216SSIM Specs, Dimensions & Price Tracking ... applianceiq.ai	Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.6875 in plus documented top cleara
Value used by ExactFit 70.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Beko BFBD30216SSIM Specs, Dimensions & Price Tracking ... applianceiq.ai · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.6875 in plus documented top cleara Reviewed: 2026-09-05 Minimum opening height derived from highest appliance endpoint 69.6875 in plus documented top clearance 1.0 in. Open original source ↗ Why this value was used Minimum opening height derived from highest appliance endpoint 69.6875 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25.25 in	✓ Verified — equivalent model · Calculated/inferred	Beko BFBD30216SS Spec Sheet assets.skulytics.io	Page 4
Value used by ExactFit 25.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Beko BFBD30216SS Spec Sheet assets.skulytics.io · Spec Sheet Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 24.4375 in plus propagated rear clearance 0.8125 in. Open original source ↗ Why this value was used Minimum opening depth derived from case-only depth 24.4375 in plus propagated rear clearance 0.8125 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Why evidence from BFBD30216SS applies Target model: BFBD30216SSIM. Supporting model: BFBD30216SS. Manufacturer: Beko. Product family and measurement relationship: depth_case_only_in + rear_clearance_in. Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth derived from case-only depth 24.4375 in plus propagated rear clearance 0.8125 in.. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.5625 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 4
Value used by ExactFit 0.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Open original source ↗ Why this value was used Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.5625 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 4
Value used by ExactFit 0.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Open original source ↗ Why this value was used Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	1 in	✓ Secondary source only	Beko BFBD30216SSIM Specs, Dimensions & Price Tracking ... applianceiq.ai	Retained specification excerpt: Top Air Clearances\":\"1 in
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Beko BFBD30216SSIM Specs, Dimensions & Price Tracking ... applianceiq.ai · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Top Air Clearances\":\"1 in Reviewed: 2026-09-05 Top Air Clearances\":\"1 in Open original source ↗ Why this value was used Top Air Clearances\":\"1 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	0.8125 in	✓ Verified — equivalent model · Calculated/inferred	Beko BFBD30216SS Spec Sheet assets.skulytics.io	Page 4
Value used by ExactFit 0.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBD30216SS Confidence label: medium. Primary evidence Beko BFBD30216SS Spec Sheet assets.skulytics.io · Spec Sheet Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SS; original evidence: Allow 13/16" (30 mm) minimum clearance at rear Open original source ↗ Why this value was used Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SS; original evidence: Allow 13/16" (30 mm) minimum clearance at rear Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBD30216SS. Why evidence from BFBD30216SS applies Target model: BFBD30216SSIM. Supporting model: BFBD30216SS. Manufacturer: Beko. Product family and measurement relationship: exact 8-dimension chassis signature; source model Beko BFBD30216SS. Measurement transferred: Rear clearance. Relevant equivalence evidence: Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SS; original evidence: Allow 13/16" (30 mm) minimum clearance at rear. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	0.5625 in	✓ Secondary source only	Beko BFBD30216SSIM Spec Sheet assets.skulytics.io	Page 4
Value used by ExactFit 0.5625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko BFBD30216SSIM Spec Sheet assets.skulytics.io · Spec Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Exact-model manufacturer sheet supplies the numeric side installation baseline; no larger fixed-wall minimum is specified. Open original source ↗ Why this value was used Exact-model manufacturer sheet supplies the numeric side installation baseline; no larger fixed-wall minimum is specified. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	29.75 in	✓ Secondary source only	Beko BFBD30216SSIM Spec Sheet assets.skulytics.io	Page 2
Value used by ExactFit 29.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko BFBD30216SSIM Spec Sheet assets.skulytics.io · Spec Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 H x W x D) (in) 69 11 11/16 16 x 29 3/4 x 29 13 13/16 16 Open original source ↗ Why this value was used H x W x D) (in) 69 11 11/16 16 x 29 3/4 x 29 13 13/16 16 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	0.5625 in	✓ Verified — exact model	Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko	Page 4
Value used by ExactFit 0.5625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf Beko · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Installation top view: 9/16 in minimum at each side Open original source ↗ Why this value was used Installation top view: 9/16 in minimum at each side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Depth without door

Selected: 24.4375 in. Earlier retained values: 25.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Cabinet depth 24 7/16 in

View source scope, location, and impact on fit

Depth with door, without handles

Selected: 27.5625 in. Earlier retained values: 29.8125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth with door 27 9/16 in, excluding handle

View source scope, location, and impact on fit

Source documents and pages

Beko BFBD30216SSIM Spec Sheet

assets.skulytics.io · Spec Sheet · secondary model/source

Model numbers covered: BFBD30216SSIM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

3 displayed measurements supported: Overall width; Hinge-side wall clearance; Cabinet case width.