Measurement evidence for Beko BFBD30216SS

Value used by ExactFit

29.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.4375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

• 25.5625 in — superseded

  104280914.pdf; page 4. Model scope: not separately recorded. Raw value: Depth of cabinet 259/16" (650 mm). The final reviewed registry supersedes this earlier audit value. Exact BFBD30216 chassis specification and installation drawings.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.5625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

• 29.8125 in — superseded

  104280914.pdf; page 3. Model scope: not separately recorded. Raw value: Depth with door 2913/16" (758 mm). The final reviewed registry supersedes this earlier audit value. Exact BFBD30216 chassis specification and installation drawings.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.8125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

55.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

• 30.75 in — superseded

  104280914.pdf + 104280926.pdf; page 11. Model scope: not separately recorded. Raw value: Minimum opening derived from exact product width plus explicit symmetric side spacing: 29.75 + 2 * 0.5 = 30.75 in. Side evidence: around the product for proper functionality. This | refrigerator requires at least 2" from the top of the unit to | the ceiling or enclosure, 1/2" on each side and 1 3/16" in the | deterministic pattern: clearance_each_side. The final reviewed registry supersedes this earlier audit value. Exact BFBD30216 chassis specification and installation drawings.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Beko BFBD30216SSIM Specs, Dimensions & Price Tracking ...
applianceiq.ai · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.6875 in plus propagated top cleara
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 69.6875 in plus propagated top clearance 1.0 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 69.6875 in plus propagated top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.4375 in plus documented rear clearance 0.8125 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.4375 in plus documented rear clearance 0.8125 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM

Confidence label: medium.

Primary evidence

Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf
Beko · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM

Confidence label: medium.

Primary evidence

Beko measurement source — https://www.beko.com/content/dam/united-states-us-aem/united-states-us-aemProductCatalog/product-documents/8700000762-BFBD30216SSIM/en-US-8700000762-202304051742300-Product-Formen-US.pdf
Beko · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Legacy reviewed field migration; endpoint indicators=['each side']; Installation top view: 9/16 in minimum at each side Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM

Confidence label: medium.

Primary evidence

Beko BFBD30216SSIM Specs, Dimensions & Price Tracking ...
applianceiq.ai · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evide
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Top Air Clearances\":\"1 in

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Beko BFBD30216SSIM; original evidence: Top Air Clearances\":\"1 in Calculation or inference: exact 8-dimension chassis signature; source model Beko BFBD30216SSIM.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Allow 13/16" (30 mm) minimum clearance at rear

Why this value was used

Allow 13/16" (30 mm) minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Exact-model manufacturer sheet supplies the numeric side installation baseline; no larger fixed-wall minimum is specified.

Why this value was used

Exact-model manufacturer sheet supplies the numeric side installation baseline; no larger fixed-wall minimum is specified.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.5625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Beko BFBD30216SS Spec Sheet
assets.skulytics.io · Spec Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Exact BFBD30216 chassis specification and installation drawings.

Why this value was used

Exact BFBD30216 chassis specification and installation drawings.

Other evidence found

• 0.5 in — superseded

  104280926.pdf; page 11. Model scope: not separately recorded. Raw value: around the product for proper functionality. This | refrigerator requires at least 2" from the top of the unit to | the ceiling or enclosure, 1/2" on each side and 1 3/16" in the | deterministic pattern: clearance_each_side. The final reviewed registry supersedes this earlier audit value. Exact BFBD30216 chassis specification and installation drawings.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.