This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-25. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280339.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280339.pdf Exact-model dimensional and 90-degree installation drawings.Open original source ↗ Why this value was usedExact-model dimensional and 90-degree installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5 in | ✓ Conflicting sources — resolved | Beko installation document — 104280339.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280339.pdf Exact-model dimensional and 90-degree installation drawings.Open original source ↗ Why this value was usedExact-model dimensional and 90-degree installation drawings. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280339.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280339.pdf Exact-model dimensional and 90-degree installation drawings.Open original source ↗ Why this value was usedExact-model dimensional and 90-degree installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.625 in | ✓ Conflicting sources — resolved | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf Depth Without Doors 21 7/8" with the note "Add 1 3/4" (44.4 mm) for spacers on back". Case-only depth includes fixed rear spacers (owner Rule B); same reading as the verified BBBF3019IMWESS.Open original source ↗ Why this value was usedDepth Without Doors 21 7/8" with the note "Add 1 3/4" (44.4 mm) for spacers on back". Case-only depth includes fixed rear spacers (owner Rule B); same reading as the verified BBBF3019IMWESS. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.3125 in | ✓ Verified — retained secondary source | Beko installation document — 104280339.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24.3125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280339.pdf Exact-model dimensional and 90-degree installation drawings.Open original source ↗ Why this value was usedExact-model dimensional and 90-degree installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.75 in | ✓ Conflicting sources — resolved · Calculated/inferred | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit26.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: matching factory-panel chassis handle projection Confidence label: medium. Primary evidenceBeko measurement source — 104280339.pdf Panel-ready handle depth varies; standardized to the matching factory-handle chassis.Open original source ↗ Why this value was usedPanel-ready handle depth varies; standardized to the matching factory-handle chassis. Calculation or inference: matching factory-panel chassis handle projection. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 55.5 in | ✓ Conflicting sources — resolved | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit55.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf Door-swing drawing: 55 1/2" (1409 mm) with the door at 90 degrees; same value as the verified BBBF3019IMWESS.Open original source ↗ Why this value was usedDoor-swing drawing: 55 1/2" (1409 mm) with the door at 90 degrees; same value as the verified BBBF3019IMWESS. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30 in | ✓ Verified — retained secondary source | Beko installation document — 104280339.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280339.pdf Exact-model dimensional and 90-degree installation drawings.Open original source ↗ Why this value was usedExact-model dimensional and 90-degree installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf Exact-model manufacturer product sheet explicitly specifies an 84 in cutout height.Open original source ↗ Why this value was usedExact-model manufacturer product sheet explicitly specifies an 84 in cutout height. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Beko measurement source — 00580ee1107aa10558d6450ba9b9c263991d4c8030222b96341dd82860044d65.pdf images.webfronts.com | Page 2 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: corrected from full-page labeled dimension context Confidence label: high. Primary evidenceBeko measurement source — 00580ee1107aa10558d6450ba9b9c263991d4c8030222b96341dd82860044d65.pdf Cutout Requirements 24 5/16"Open original source ↗ Why this value was usedCutout Requirements 24 5/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf Exact-model manufacturer sheet specifies an 84 in opening and 1/8 in top/side and 1/2 in rear clearances.Open original source ↗ Why this value was usedExact-model manufacturer sheet specifies an 84 in opening and 1/8 in top/side and 1/2 in rear clearances. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf Exact-model manufacturer sheet specifies an 84 in opening and 1/8 in top/side and 1/2 in rear clearances.Open original source ↗ Why this value was usedExact-model manufacturer sheet specifies an 84 in opening and 1/8 in top/side and 1/2 in rear clearances. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Verified — retained secondary source | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf Exact-model manufacturer sheet specifies an 84 in opening and 1/8 in top/side and 1/2 in rear clearances.Open original source ↗ Why this value was usedExact-model manufacturer sheet specifies an 84 in opening and 1/8 in top/side and 1/2 in rear clearances. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.5 in | ✓ Verified — retained secondary source | Beko measurement source — 104280339.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence Confidence label: high. Primary evidenceBeko measurement source — 104280339.pdf full-page adjudication=0.5; parser candidates=[2.0, 0.118]; 2" (13 mm) minimum clearance at rearOpen original source ↗ Why this value was usedfull-page adjudication=0.5; parser candidates=[2.0, 0.118]; 2" (13 mm) minimum clearance at rear Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.75 in | ? Verified — finalized database measurement | Beko measurement source — 104280339.pdf Publisher not recorded | Page 3 | |
Value used by ExactFit2.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceBeko measurement source — 104280339.pdf Exact-model Beko spec sheet (panel ready), top view with the door open 90°: 2 3/4" (70 mm)* beyond the cabinet side; *may vary with panel thickness and handle design. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model Beko spec sheet (panel ready), top view with the door open 90°: 2 3/4" (70 mm)* beyond the cabinet side; *may vary with panel thickness and handle design. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.75 in | ✓ Verified — retained secondary source | Beko installation document — 104280339.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280339.pdf Exact-model dimensional and 90-degree installation drawings.Open original source ↗ Why this value was usedExact-model dimensional and 90-degree installation drawings. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 83.5 in. Earlier retained values: 83.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model dimensional and 90-degree installation drawings.
View source scope, location, and impact on fitSelected: 23.625 in. Earlier retained values: 21.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Depth Without Doors 21 7/8" with the note "Add 1 3/4" (44.4 mm) for spacers on back". Case-only depth includes fixed rear spacers (owner Rule B); same reading as the verified BBBF3019IMWESS.
View source scope, location, and impact on fitSelected: 26.75 in. Earlier retained values: 83.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Panel-ready handle depth varies; standardized to the matching factory-handle chassis. Calculation or inference: matching factory-panel chassis handle projection.
View source scope, location, and impact on fitSelected: 55.5 in. Earlier retained values: 32.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Door-swing drawing: 55 1/2" (1409 mm) with the door at 90 degrees; same value as the verified BBBF3019IMWESS.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: BBBF3019IMWE. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗images.webfronts.com · Web source · secondary model/source
Model numbers covered: BBBF3019IMWE. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.