This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 21.625 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.4375 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit71.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 71.4375 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit71.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 21.625 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 21.625 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 21.625 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Beko measurement source — 104280323.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit43.25 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case/door depth + door width Confidence label: medium. Primary evidenceBeko measurement source — 104280323.pdf Geometric 90-degree envelope for the exact 21 5/8-in chassis.Open original source ↗ Why this value was usedGeometric 90-degree envelope for the exact 21 5/8-in chassis. Calculation or inference: case/door depth + door width. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 25.625 in | ✓ Verified — retained secondary source · Calculated/inferred | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit25.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 21.625 + 2 * 2.0 Confidence label: medium. Primary evidenceBeko measurement source — 104280326.pdf Manual requires 2 in to the wall on each side.Open original source ↗ Why this value was usedManual requires 2 in to the wall on each side. Calculation or inference: 21.625 + 2 * 2.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 73.4375 in | ✓ Verified — retained secondary source · Calculated/inferred | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit73.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceBeko measurement source — 104280326.pdf Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.Open original source ↗ Why this value was usedMinimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 23.625 in | ✓ Verified — retained secondary source · Calculated/inferred | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceBeko measurement source — 104280326.pdf Minimum opening depth is the verified cabinet depth plus the documented rear clearance.Open original source ↗ Why this value was usedMinimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280326.pdf Manufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall.Open original source ↗ Why this value was usedManufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280326.pdf Manufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall.Open original source ↗ Why this value was usedManufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280326.pdf Manufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall.Open original source ↗ Why this value was usedManufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Beko measurement source — 104280326.pdf assets.skulytics.io | Page 14 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko measurement source — 104280326.pdf Manufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall.Open original source ↗ Why this value was usedManufacturer manual requires at least 5 cm (approximately 2 in) from the ceiling and wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 21.625 in | ✓ Verified — retained secondary source | Beko installation document — 104280323.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit21.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBeko installation document — 104280323.pdf Exact-model product sheet dimensions.Open original source ↗ Why this value was usedExact-model product sheet dimensions. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: BBBF2410IM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: BBBF2410IM. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.