Measurement evidence for Amana ARTX3028PB

Value used by ExactFit

28 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana installation document — 90391298.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

F Width - Cabinet = 28"

Why this value was used

F Width - Cabinet = 28"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — 90391298.pdf
Amana · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Visually reviewed shared exact-model guide: B - Height, Top of Cabinet = 65 3/8 in.

Why this value was used

Visually reviewed shared exact-model guide: B - Height, Top of Cabinet = 65 3/8 in.

Other evidence found

• 65.38 in — superseded

  www.amana.com; location not retained. Model scope: not separately recorded. Raw value: Sibling-chassis propagation from ARTX3028PW; model codes have the same numeric skeleton, at least four existing chassis dimensions match, and no structural dimensions conflict. Sibling evidence: Height To Top Of Cabinet: 65.38 in | 5 in Freezer Capacity Volume 4.03 cu. ft. Gross Weight 180 lbs Height 65.625 in Height To Top Of Cabinet 65.375 in Height To Top Of Door Hinge 65.625 in Height To Top Of Door Trim 66.625 in Maxi. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — 90391298.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Visually reviewed shared exact-model guide: A - Height Overall = 66 5/8 in; canonical highest installed-height endpoint.

Why this value was used

Visually reviewed shared exact-model guide: A - Height Overall = 66 5/8 in; canonical highest installed-height endpoint.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — p.top-freezer-refrigerator-16.3-cu.-ft.artx3028pw.html
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model Amana specification: Depth Excluding Doors = 27 5/8 in. The planning-guide cell
Reviewed: 2026-09-09

Official exact-model Amana specification: Depth Excluding Doors = 27 5/8 in. The planning-guide cell reading 21 7/8 in is rejected because it is paired with 81 cm and conflicts with the diagram.

Why this value was used

Official exact-model Amana specification: Depth Excluding Doors = 27 5/8 in. The planning-guide cell reading 21 7/8 in is rejected because it is paired with 81 cm and conflicts with the diagram.

Other evidence found

• 27.5 in — superseded

  Document 90391298.pdf; page 1. Model scope: not separately recorded. Raw value: E Depth - Cabinet = 27 1/2". The final reviewed registry supersedes this earlier audit value.

• 21.875 in — superseded

  Document 90391298.pdf; page 1. Model scope: not separately recorded. Raw value: E - Depth, Cabinet Only = 21 7/8 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — 90391298.pdf
Amana · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Visually reviewed shared exact-model guide: D - Depth, Overall = 31 7/8 in; no separate handle projection is shown.

Why this value was used

Visually reviewed shared exact-model guide: D - Depth, Overall = 31 7/8 in; no separate handle projection is shown.

Other evidence found

• 31.88 in — superseded

  www.amana.com; location not retained. Model scope: not separately recorded. Raw value: Sibling-chassis propagation from ARTX3028PW; model codes have the same numeric skeleton, at least four existing chassis dimensions match, and no structural dimensions conflict. Sibling evidence: Depth Closed Excluding Handles: 31.88 in | s Cabinet Width 28 in Capacity 16.3 cu. ft. Common Size 28"" in Depth 31.875 in Depth Closed Excluding Handles 31.875 in Depth Closed Including Handles 31.875 in Depth Excluding Doors 27.625 in Depth . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana installation document — 90391298.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

D Depth - Overall = 31 7/8"

Why this value was used

D Depth - Overall = 31 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana installation document — 90391298.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

C Depth - Door Open 90° = 56 7/8"

Why this value was used

C Depth - Door Open 90° = 56 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * exact/family installation side clearance

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

Amana measurement source — dimension-guide-w11685534-revA.pdf
Amana · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official family dimension guide: recommended 1/2 in space on each side.
Reviewed: 2026-09-04

Official family dimension guide: recommended 1/2 in space on each side.

Why this value was used

Official family dimension guide: recommended 1/2 in space on each side. Calculation or inference: width_doors_closed_in + 2 * exact/family installation side clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in, height_hinge_in) + top_clearance_in

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Amana measurement source — 90391298.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-19

Recalculated 2026-09-19 with the stored formula from current inputs: max(height_case_in, height_hinge_in) + top_clearance_in with height_case_in = 65.375, height_hinge_in = 66.625, top_clearance_in = 3 = 69.625 in (previously 67.125 in).

Why this value was used

Recalculated 2026-09-19 with the stored formula from current inputs: max(height_case_in, height_hinge_in) + top_clearance_in with height_case_in = 65.375, height_hinge_in = 66.625, top_clearance_in = 3 = 69.625 in (previously 67.125 in). Calculation or inference: max(height_case_in, height_hinge_in) + top_clearance_in.

Other evidence found

• 67.125 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Installation envelope: max(case 65.38, hinge 66.625) + 0.5 in top = 67.125 in.. The final reviewed registry supersedes this earlier audit value.

• 67.125 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Installation envelope from direct overall height and top clearance: 66.625 + 0.5 = 67.125 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Amana measurement source — p.top-freezer-refrigerator-16.3-cu.-ft.artx3028pw.html
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation envelope from valid cabinet-only depth and direct rear clearance: 27.625 + 1 = 28.625 i
Reviewed: 2026-09-09

Installation envelope from valid cabinet-only depth and direct rear clearance: 27.625 + 1 = 28.625 in.

Why this value was used

Installation envelope from valid cabinet-only depth and direct rear clearance: 27.625 + 1 = 28.625 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

• 28.5 in — superseded

  Document 90391298.pdf; page 2. Model scope: not separately recorded. Raw value: Installation envelope: 27.5 in case depth + 1 in rear = 28.5 in.. The final reviewed registry supersedes this earlier audit value.

• 22.875 in — superseded

  Document 90391298.pdf; page 1. Model scope: not separately recorded. Raw value: Installation envelope from direct cabinet-only depth and rear clearance: 21.875 + 1 = 22.875 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern ARTX3028P***

Confidence label: high.

Primary evidence

Amana measurement source — dimension-guide-w11685534-revA.pdf
Amana · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern ARTX3028P***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern ARTX3028P***

Confidence label: high.

Primary evidence

Amana measurement source — dimension-guide-w11685534-revA.pdf
Amana · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern ARTX3028P***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — 90391298.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-19

Location requirements drawing: 3" (7.5 cm) between the refrigerator top and the overhead cabinet. The text on the same page recommends 1/2" "on each side and between overhead cabinets and refrigerator top"; the drawing is used, consistent with the ARTX2014/ARTX2314 guides, which print 3". Owner decision 2026-09-19.

Why this value was used

Location requirements drawing: 3" (7.5 cm) between the refrigerator top and the overhead cabinet. The text on the same page recommends 1/2" "on each side and between overhead cabinets and refrigerator top"; the drawing is used, consistent with the ARTX2014/ARTX2314 guides, which print 3". Owner decision 2026-09-19.

Other evidence found

• 0.5 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Exact ARTX3028 guide: allow 1/2" between overhead cabinets and refrigerator top.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — 90391298.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact ARTX3028 guide: allow at least 1" between back of cabinet and wall.

Why this value was used

Exact ARTX3028 guide: allow at least 1" between back of cabinet and wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana measurement source — 90391298.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-16

Amana planning sheet W11685534A (07/23) for ARTX3028PB/PW, French p.4: "laisser 3 3/4 po (9,5 cm) d'espace du côté de la charnière (selon le modèle) pour permettre à la porte de s'ouvrir"; Spanish p.6: "deje 3 3/4" (9,5 cm) del lado de la bisagra ... para permitir que la puerta abra bien". English p.2 prints 2" (5.08 cm). The translations' headers call the model bottom-freezer, but they reuse the top-mount drawing and name the same models. The larger printed door-swing clearance is stored (owner decision 2026-10-16).

Why this value was used

Amana planning sheet W11685534A (07/23) for ARTX3028PB/PW, French p.4: "laisser 3 3/4 po (9,5 cm) d'espace du côté de la charnière (selon le modèle) pour permettre à la porte de s'ouvrir"; Spanish p.6: "deje 3 3/4" (9,5 cm) del lado de la bisagra ... para permitir que la puerta abra bien". English p.2 prints 2" (5.08 cm). The translations' headers call the model bottom-freezer, but they reuse the top-mount drawing and name the same models. The larger printed door-swing clearance is stored (owner decision 2026-10-16).

Other evidence found

• 2 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Exact ARTX3028 guide: leave 2" minimum on hinge side next to a fixed wall; replaces misclassified 1/2" ventilation value.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Amana installation document — 90391298.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

F Width - Cabinet = 28"

Why this value was used

F Width - Cabinet = 28"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.