This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-17. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Measurements and supporting evidence
Measurement
Value used
Evidence status
Primary source
Location
Details
Overall width
35.625 in
? Verified — finalized database measurement
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
35.625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 4
Value used by ExactFit
71.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-10-17
left PRODUCT DIMENSIONS perspective drawing: 71 1/2 in (1815 mm), floor to the top of the cabinet, below the highest hinge/top projection.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
left PRODUCT DIMENSIONS perspective drawing: 71 1/2 in (1815 mm), floor to the top of the cabinet, below the highest hinge/top projection.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 1
Value used by ExactFit
72 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-17
GENERAL FEATURES: 72 in (? mm), floor to the overall top of the appliance.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
GENERAL FEATURES: 72 in (? mm), floor to the overall top of the appliance.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 4
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-10-17
right PRODUCT DIMENSIONS side elevation: 25 in (635 mm), rear face of the fixed spacers to the front plane of the upper case.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
right PRODUCT DIMENSIONS side elevation: 25 in (635 mm), rear face of the fixed spacers to the front plane of the upper case.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
DIMENSIONS AND WEIGHT table: 28 3/4 in (? mm), rear face of the fixed rear spacers to the front face of the closed doors.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
DIMENSIONS AND WEIGHT table: 28 3/4 in (? mm), rear face of the fixed rear spacers to the front face of the closed doors.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
31.4375 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
DIMENSIONS AND WEIGHT table: 31 7/16 in (? mm), rear face of the fixed rear spacers to the frontmost handle.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
DIMENSIONS AND WEIGHT table: 31 7/16 in (? mm), rear face of the fixed rear spacers to the frontmost handle.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 3
Value used by ExactFit
43.375 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-17
TOP VIEW CLEARANCE drawing: 43 3/8 in (1102 mm), rear face of the fixed rear spacers to the forwardmost edge of a door in the dashed 90° position.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
TOP VIEW CLEARANCE drawing: 43 3/8 in (1102 mm), rear face of the fixed rear spacers to the forwardmost edge of a door in the dashed 90° position.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
36 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
DIMENSIONS AND WEIGHT table: 36 in (? mm), left side to right side of the required opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
DIMENSIONS AND WEIGHT table: 36 in (? mm), left side to right side of the required opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
72 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
DIMENSIONS AND WEIGHT table: 72 in (? mm), bottom to top of the required opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
DIMENSIONS AND WEIGHT table: 72 in (? mm), bottom to top of the required opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
DIMENSIONS AND WEIGHT table: 25 in (? mm), rear to front of the required opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
DIMENSIONS AND WEIGHT table: 25 in (? mm), rear to front of the required opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 4
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-10-17
lower PRODUCT DIMENSIONS top-view depth-ladder drawing: 1/8 in (3 mm), left appliance side to left inside face of the cavity.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
lower PRODUCT DIMENSIONS top-view depth-ladder drawing: 1/8 in (3 mm), left appliance side to left inside face of the cavity.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 4
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-10-17
lower PRODUCT DIMENSIONS top-view depth-ladder drawing: 1/8 in (3 mm), left appliance side to left inside face of the cavity.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
lower PRODUCT DIMENSIONS top-view depth-ladder drawing: 1/8 in (3 mm), left appliance side to left inside face of the cavity.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 3
Value used by ExactFit
0.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-17
ventilation note beside CUTOUT DIMENSIONS: 1/2 in (12.7 mm), top of the refrigerator to the surface above it.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
ventilation note beside CUTOUT DIMENSIONS: 1/2 in (12.7 mm), top of the refrigerator to the surface above it.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 3
Value used by ExactFit
1 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-17
ventilation note beside CUTOUT DIMENSIONS: 1 in (25.4 mm), rear of the refrigerator to the wall or rear surface behind it.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
ventilation note beside CUTOUT DIMENSIONS: 1 in (25.4 mm), rear of the refrigerator to the wall or rear surface behind it.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 3
Value used by ExactFit
4.4375 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-17
Top view clearance: 4 7/16" from the cabinet side to the Professional handle with the left door at 90° (1 3/4" to the door face). Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Top view clearance: 4 7/16" from the cabinet side to the Professional handle with the left door at 90° (1 3/4" to the door face). Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 3
Value used by ExactFit
11.125 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-17
Top view clearance: 11 1/8" from the cabinet side to the fully opened right door at 118°. Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Top view clearance: 11 1/8" from the cabinet side to the fully opened right door at 118°. Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded
Page 2
Value used by ExactFit
35.625 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Thermador measurement source — web-e31a9171d0.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
DIMENSIONS AND WEIGHT table: 35 5/8 in (? mm), outer left side to outer right side of the closed appliance.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
DIMENSIONS AND WEIGHT table: 35 5/8 in (? mm), outer left side to outer right side of the closed appliance.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-17.
17 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
