This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-17. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Measurements and supporting evidence
Measurement
Value used
Evidence status
Primary source
Location
Details
Overall width
35.625 in
? Verified — finalized database measurement
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 1
Value used by ExactFit
35.625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-17
page 1 'Appliance dimensions with hinges, handles and doors (H x W x D)'; page 2 prints the same width in the plan: 35 5/8 in (905 mm), widest left-to-right extent of the appliance with hinges, handles and doors.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 1 'Appliance dimensions with hinges, handles and doors (H x W x D)'; page 2 prints the same width in the plan: 35 5/8 in (905 mm), widest left-to-right extent of the appliance with hinges, handles and doors.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
71.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 perspective and side view; page 1 without-hinges-and-doors H x W x D row: 71 1/2 in (1815 mm), floor at the bottom of the cabinet to the top of the cabinet body, excluding the top hinge projection.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 perspective and side view; page 1 without-hinges-and-doors H x W x D row: 71 1/2 in (1815 mm), floor at the bottom of the cabinet to the top of the cabinet body, excluding the top hinge projection.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
72 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 perspective and side view; page 1 overall and no-handles H x W x D rows: 72 in (1830 mm), floor to the highest top hinge/door projection.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 perspective and side view; page 1 overall and no-handles H x W x D rows: 72 in (1830 mm), floor to the highest top hinge/door projection.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 side-view depth ladder and closed-installation plan: 25 in (635 mm), rear face of the fixed rear spacers to the front face of the cabinet body, excluding doors and handles.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 side-view depth ladder and closed-installation plan: 25 in (635 mm), rear face of the fixed rear spacers to the front face of the cabinet body, excluding doors and handles.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 side-view ladder and closed-installation plan; page 1 'with hinges and doors, no handles' row: 28 3/4 in (731 mm), rear face of the fixed rear spacers to the front face of the closed doors.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 side-view ladder and closed-installation plan; page 1 'with hinges and doors, no handles' row: 28 3/4 in (731 mm), rear face of the fixed rear spacers to the front face of the closed doors.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
31.125 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 closed-installation plan; page 1 overall H x W x D row: 31 1/8 in (790 mm), rear face of the fixed rear spacers to the frontmost face of the handles.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 closed-installation plan; page 1 overall H x W x D row: 31 1/8 in (790 mm), rear face of the fixed rear spacers to the frontmost face of the handles.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
43.375 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 open-door plan: 43 3/8 in (1102 mm), rear face of the fixed rear spacers to the forwardmost extent of a refrigerator door in the dashed 90-degree position.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 open-door plan: 43 3/8 in (1102 mm), rear face of the fixed rear spacers to the forwardmost extent of a refrigerator door in the dashed 90-degree position.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
36 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 cutout drawing; page 1 required cutout H x W x D row: 36 in (914 mm), left inside face to right inside face of the installation opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 cutout drawing; page 1 required cutout H x W x D row: 36 in (914 mm), left inside face to right inside face of the installation opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
72 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 cutout drawing; page 1 required cutout H x W x D row: 72 in (1830 mm), floor to underside/top boundary of the installation opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 cutout drawing; page 1 required cutout H x W x D row: 72 in (1830 mm), floor to underside/top boundary of the installation opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 cutout drawing; page 1 required cutout H x W x D row and double-asterisk footnote: 25 in (635 mm), rear wall of the installation opening to its front edge.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 cutout drawing; page 1 required cutout H x W x D row and double-asterisk footnote: 25 in (635 mm), rear wall of the installation opening to its front edge.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 closed-installation plan: 1/8 in (3 mm), left side of the appliance to the left side of the cabinet opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 closed-installation plan: 1/8 in (3 mm), left side of the appliance to the left side of the cabinet opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 closed-installation plan: 1/8 in (3 mm), left side of the appliance to the left side of the cabinet opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 closed-installation plan: 1/8 in (3 mm), left side of the appliance to the left side of the cabinet opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
0.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 installation note: 1/2 in (12.7 mm), top of the refrigerator cabinet to the top of the opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 installation note: 1/2 in (12.7 mm), top of the refrigerator cabinet to the top of the opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
1 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 installation note and closed-installation plan; page 1 says the 25 in cutout includes the required 1 in airflow: 1 in (25.4 mm), rear of the refrigerator cabinet to the rear wall of the opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 installation note and closed-installation plan; page 1 says the 25 in cutout includes the required 1 in airflow: 1 in (25.4 mm), rear of the refrigerator cabinet to the rear wall of the opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
3.6875 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
Installation Details door-swing plan: 3 11/16" (93) from the cabinet side to the handle with the left door at 90° (1 3/4" (45) to the door face). Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Installation Details door-swing plan: 3 11/16" (93) from the cabinet side to the handle with the left door at 90° (1 3/4" (45) to the door face). Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
10.9375 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
Door-swing plan: 10 15/16" (278) from the cabinet side to the fully opened right door at 118°. Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Door-swing plan: 10 15/16" (278) from the cabinet side to the fully opened right door at 118°. Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded
Page 2
Value used by ExactFit
35.625 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-0bf9399ed6.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 perspective and open-door plan; page 1 also prints 35 5/8 in the without-hinges-and-doors H x W x D row: 35 5/8 in (905 mm), outer left side of the cabinet body to outer right side of the cabinet body, excluding the doors and handles.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 perspective and open-door plan; page 1 also prints 35 5/8 in the without-hinges-and-doors H x W x D row: 35 5/8 in (905 mm), outer left side of the cabinet body to outer right side of the cabinet body, excluding the doors and handles.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-17.
17 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
