Measurement evidence for Whirlpool WRS335SDHB

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Whirlpool WRS335SDHB fit check Check this model against your opening How ExactFit verifies measurements

Whirlpool WRS335SDHB

Side-by-Side · Standard-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Incomplete evidence

1exact-model manufacturer values

1verified equivalent/same-chassis values

9secondary-source-only values

5values with unresolved source details

Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location	Details
Overall width	35.875 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 35.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Cabinet Width E: 35 7/8" (90.11 cm) Open original source ↗ Why this value was used Cabinet Width E: 35 7/8" (90.11 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	66.625 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 66.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Height to Top of Cabinet C: 66 5/8" (169.23 cm) Open original source ↗ Why this value was used Height to Top of Cabinet C: 66 5/8" (169.23 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.625 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 69.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Overall Height D: 69 5/8" (176.85 cm) Open original source ↗ Why this value was used Overall Height D: 69 5/8" (176.85 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	28 in	✓ Verified — exact model	Whirlpool measurement source — https://www.whirlpool.com/kitchen/refrigeration/refrigerators/side-by-side/p.WRS335SDHB.html Whirlpool	Retained specification excerpt: Official exact-model product page: Depth Excluding Doors = 28 in
Value used by ExactFit 28 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool measurement source — https://www.whirlpool.com/kitchen/refrigeration/refrigerators/side-by-side/p.WRS335SDHB.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model product page: Depth Excluding Doors = 28 in Reviewed: 2026-09-04 Official exact-model product page: Depth Excluding Doors = 28 in Open original source ↗ Why this value was used Official exact-model product page: Depth Excluding Doors = 28 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	31.625 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 31.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth Without Handles A: 31 5/8" (80.33 cm) Open original source ↗ Why this value was used Depth Without Handles A: 31 5/8" (80.33 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	33.625 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 33.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth With Handles B: 33 5/8" (85.41 cm) Open original source ↗ Why this value was used Depth With Handles B: 33 5/8" (85.41 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	49.3125 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 49.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth with Doors Open 90° F: 49 5/16" (125.25 cm) Open original source ↗ Why this value was used Depth with Doors Open 90° F: 49 5/16" (125.25 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 1
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Normal minimum cabinet cutout width: 36" (91.44 cm) Open original source ↗ Why this value was used Normal minimum cabinet cutout width: 36" (91.44 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	Unknown	? Not found · Calculated/inferred	PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool	Page 1
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Minimum opening height derived from highest appliance endpoint 69.625 in plus propagated top clearance 0.5 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 70.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	Unknown	? Not found · Calculated/inferred	PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool	Page 1
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 28.0 in plus propagated rear clearance 1.0 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 29 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	Unknown	? Not found · Calculated/inferred	PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool	Page 1
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: model-series prefix WRS335SDH; 2 direct seeds; unanimous value 0.5 Confidence label: medium. Primary evidence PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Conflict-free 9-character model-series consensus (WRS335SDH) from 2 directly evidenced models; example Whirlpool WRS335SDHM: 1/2" of space on each side Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	Unknown	? Not found · Calculated/inferred	PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool	Page 1
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: model-series prefix WRS335SDH; 2 direct seeds; unanimous value 0.5 Confidence label: medium. Primary evidence PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Conflict-free 9-character model-series consensus (WRS335SDH) from 2 directly evidenced models; example Whirlpool WRS335SDHM: 1/2" of space on each side Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	Unknown	? Not found · Calculated/inferred	PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool	Page 1
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: model-series prefix WRS335SDH; 2 direct seeds; unanimous value 0.5 Confidence label: medium. Primary evidence PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Conflict-free 9-character model-series consensus (WRS335SDH) from 2 directly evidenced models; example Whirlpool WRS335SDHM: 1/2" of space on each side and at the top Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	Unknown	? Not found · Calculated/inferred	PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool	Page 1
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: model-series prefix WRS33; 2 direct seeds; unanimous value 1.0 Confidence label: medium. Primary evidence PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Conflict-free 5-character model-series consensus (WRS33) from 2 directly evidenced models; example Whirlpool WRS331SDHW: 1" of space behind Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 1 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	2 in	✓ Verified — equivalent model · Calculated/inferred	Amana ASI2175GRB Owners Manual assets.skulytics.io	Page 7
Value used by ExactFit 2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document Confidence label: high. Primary evidence Amana ASI2175GRB Owners Manual assets.skulytics.io · Owners Manual Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05 next to a fixed wall, leave a 2" (5.08 cm Open original source ↗ Why this value was used next to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document. Why evidence from ASI2175GRB applies Target model: WRS335SDHB. Supporting model: ASI2175GRB. Manufacturer: Whirlpool. Product family and measurement relationship: cached document family mapping: generic_or_unscoped_shared_document. Measurement transferred: Hinge-side wall clearance. Relevant equivalence evidence: next to a fixed wall, leave a 2" (5.08 cm. Known differences: not separately recorded. Review decision: local cached pdf native text; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.875 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 2
Value used by ExactFit 35.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Cabinet Width E: 35 7/8" (90.11 cm) Open original source ↗ Why this value was used Cabinet Width E: 35 7/8" (90.11 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	2 in	✓ Secondary source only	Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io	Page 1
Value used by ExactFit 2 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool WRS335SDHB Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Leave 2" (5.08 cm) minimum space on each side Open original source ↗ Why this value was used Leave 2" (5.08 cm) minimum space on each side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Measurements not established

Minimum cutout height

Not found for safe fit use. Sources retained: https://www.whirlpool.com/content/dam/global/documents/201710/DimensionGuide-W11105301-D-WH.pdf. Related-model record: WRS335SDHB.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Minimum cutout depth

Not found for safe fit use. Sources retained: https://www.whirlpool.com/content/dam/global/documents/201710/DimensionGuide-W11105301-D-WH.pdf. Related-model record: WRS335SDHB.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Left-side ventilation clearance

Not found for safe fit use. Sources retained: https://www.whirlpool.com/content/dam/global/documents/201710/DimensionGuide-W11105301-D-WH.pdf. Related-model record: WRS335SDHB.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Right-side ventilation clearance

Not found for safe fit use. Sources retained: https://www.whirlpool.com/content/dam/global/documents/201710/DimensionGuide-W11105301-D-WH.pdf. Related-model record: WRS335SDHB.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Top clearance

Not found for safe fit use. Sources retained: https://www.whirlpool.com/content/dam/global/documents/201710/DimensionGuide-W11105301-D-WH.pdf. Related-model record: WRS335SDHB.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Rear clearance

Not found for safe fit use. Sources retained: https://www.whirlpool.com/content/dam/global/documents/201710/DimensionGuide-W11105301-D-WH.pdf. Related-model record: WRS335SDHB.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Source documents and pages

Whirlpool WRS335SDHB Dimension Guide

assets.skulytics.io · Dimension Guide · secondary model/source

Model numbers covered: WRS335SDHB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Whirlpool measurement source — https://www.whirlpool.com/kitchen/refrigeration/refrigerators/side-by-side/p.WRS335SDHB.html

Whirlpool · Web source · exact model/source

Model numbers covered: WRS335SDHB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

1 displayed measurements supported: Depth without door.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz,

Whirlpool · Web source · Scope not established

Model numbers covered: WRS335SDHB. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

6 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Amana ASI2175GRB Owners Manual

assets.skulytics.io · Owners Manual · equivalent model/source

Model numbers covered: ASI2175GRB. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

1 displayed measurements supported: Hinge-side wall clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether WRS335SDHB fits your opening Back to Whirlpool WRS335SDHB Read the full verification methodology

Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.