This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.875 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Cabinet Width E: 35 7/8" (90.11 cm)Open original source ↗ Why this value was usedCabinet Width E: 35 7/8" (90.11 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Height to Top of Cabinet C: 68 5/8" (174.31 cm)Open original source ↗ Why this value was usedHeight to Top of Cabinet C: 68 5/8" (174.31 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.625 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit69.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Overall Height D: 69 5/8" (176.85 cm)Open original source ↗ Why this value was usedOverall Height D: 69 5/8" (176.85 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 28 in | ✓ Secondary source only | Whirlpool WRS315SDHW 36 Inch Freestanding Side By ... www.ajmadison.com | Retained specification excerpt: Depth without Door = 28.0 in | Whirlpool WRS315SDHW 36 Inch Freestanding Side By ... Depth: 33 5/8 I | |
Value used by ExactFit28 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceWhirlpool WRS315SDHW 36 Inch Freestanding Side By ... Depth without Door = 28.0 in | Whirlpool WRS315SDHW 36 Inch Freestanding Side By ... Depth: 33 5/8 Inch. Depth without Door: 28 Inch. Depth without Door and Handles: 28 Inch. Depth without Handles: 31 5/8 Inch. | cached support: ajmadison.com, southernappliances.netOpen original source ↗ Why this value was usedDepth without Door = 28.0 in | Whirlpool WRS315SDHW 36 Inch Freestanding Side By ... Depth: 33 5/8 Inch. Depth without Door: 28 Inch. Depth without Door and Handles: 28 Inch. Depth without Handles: 31 5/8 Inch. | cached support: ajmadison.com, southernappliances.net Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 31.625 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit31.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Depth Without Handles A: 31 5/8" (80.33 cm)Open original source ↗ Why this value was usedDepth Without Handles A: 31 5/8" (80.33 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 33.625 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit33.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Depth With Handles B: 33 5/8" (85.41 cm)Open original source ↗ Why this value was usedDepth With Handles B: 33 5/8" (85.41 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 49.3125 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit49.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Depth with Doors Open 90° F: 49 5/16" (125.25 cm)Open original source ↗ Why this value was usedDepth with Doors Open 90° F: 49 5/16" (125.25 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Normal minimum cabinet cutout width: 36" (91.44 cm)Open original source ↗ Why this value was usedNormal minimum cabinet cutout width: 36" (91.44 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.125 in | ✓ Secondary source only · Calculated/inferred | PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool | Page 1 | |
Value used by ExactFit70.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidencePRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Minimum opening height derived from highest stored appliance endpoint 69.625 in plus documented top clearance 0.5 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 69.625 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 29 in | ✓ Secondary source only · Calculated/inferred | PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool | Page 1 | |
Value used by ExactFit29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidencePRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.5 in | ✓ Verified — exact model · Calculated/inferred | PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD**** Confidence label: high. Primary evidencePRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, 1/2" of space on each sideOpen original source ↗ Why this value was used1/2" of space on each side Calculation or inference: documented DOE model pattern WRS315SD****. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.5 in | ✓ Verified — exact model · Calculated/inferred | PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD**** Confidence label: high. Primary evidencePRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, 1/2" of space on each sideOpen original source ↗ Why this value was used1/2" of space on each side Calculation or inference: documented DOE model pattern WRS315SD****. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — exact model · Calculated/inferred | PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD**** Confidence label: high. Primary evidencePRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, 1/2" of space on each side and at the topOpen original source ↗ Why this value was used1/2" of space on each side and at the top Calculation or inference: documented DOE model pattern WRS315SD****. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — exact model · Calculated/inferred | PRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, Whirlpool | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD**** Confidence label: medium. Primary evidencePRODUCT MODEL NUMBERS Side by Side Refrigerator Electrical: A 115-volt, 60-Hz, 1" of space behindOpen original source ↗ Why this value was used1" of space behind Calculation or inference: documented DOE model pattern WRS315SD****. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 2 in | ✓ Verified — equivalent model · Calculated/inferred | Amana ASI2175GRB Owners Manual assets.skulytics.io | Page 7 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document Confidence label: high. Primary evidenceAmana ASI2175GRB Owners Manual next to a fixed wall, leave a 2" (5.08 cmOpen original source ↗ Why this value was usednext to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document. Why evidence from ASI2175GRB appliesTarget model: WRS315SDHW. Supporting model: ASI2175GRB. Manufacturer: Whirlpool. Product family and measurement relationship: cached document family mapping: generic_or_unscoped_shared_document. Measurement transferred: Hinge-side wall clearance. Relevant equivalence evidence: next to a fixed wall, leave a 2" (5.08 cm. Known differences: not separately recorded. Review decision: local cached pdf native text; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.875 in | ✓ Secondary source only | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit35.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Cabinet Width E: 35 7/8" (90.11 cm)Open original source ↗ Why this value was usedCabinet Width E: 35 7/8" (90.11 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 0.5 in | ✓ Conflicting sources — resolved | Whirlpool WRS315SDHW Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool WRS315SDHW Dimension Guide Allow 1/2 in. of space on each side and at the top.Open original source ↗ Why this value was usedAllow 1/2 in. of space on each side and at the top. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 0.5 in. Earlier retained values: 2 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Allow 1/2 in. of space on each side and at the top.
View source scope, location, and impact on fitassets.skulytics.io · Dimension Guide · secondary model/source
Model numbers covered: WRS315SDHW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.ajmadison.com · Web source · secondary model/source
Model numbers covered: WRS315SDHW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth without door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Whirlpool · Web source · exact model/source
Model numbers covered: WRS315SDHW. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
6 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Owners Manual · equivalent model/source
Model numbers covered: ASI2175GRB. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Hinge-side wall clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.