Measurement evidence for Whirlpool WRMF3736SV

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Closed product width mapped from documented cabinet width; doors do not project laterally when closed

Confidence label: medium.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

WRMF3736S* cabinet width G: 35 13/16"; same closed-width mapping as finish sibling WRMF3736SW.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 35.8125 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

C* Height to top of cabinet -> 69" (1753 mm)

Why this value was used

C* Height to top of cabinet -> 69" (1753 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

36 in. 29 cu. ft. Standard Depth French Door Refrigerator in ...
www.homedepot.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Door Hinge = 70.0625 in | 36 in. 29 cu. ft. Standard Depth French Door Refrigerator
Reviewed: 2026-09-04

Height to Top of Door Hinge = 70.0625 in | 36 in. 29 cu. ft. Standard Depth French Door Refrigerator in ... Height to Top of Door Hinge (in.) 70.0625 in. Height to Top of Refrigerator Case (in.) 69 in. Height to Top of Refrigerator D

Why this value was used

Height to Top of Door Hinge = 70.0625 in | 36 in. 29 cu. ft. Standard Depth French Door Refrigerator in ... Height to Top of Door Hinge (in.) 70.0625 in. Height to Top of Refrigerator Case (in.) 69 in. Height to Top of Refrigerator D

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

F Depth without doors -> 297/8" (758.8 mm)

Why this value was used

F Depth without doors -> 297/8" (758.8 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

E Depth with doors -> 34 3/4" (882.3 mm)

Why this value was used

E Depth with doors -> 34 3/4" (882.3 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

WRMF3736S* dimension E, Depth with doors: 34 3/4" (882.3 mm); integrated-handle design.

Why this value was used

WRMF3736S* dimension E, Depth with doors: 34 3/4" (882.3 mm); integrated-handle design.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

49 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Whirlpool WRMF3736SV 36 Inch Freestanding 4-Door ...
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: rlpool WRMF3736SV 36 Inch Freestanding 4-Door ... Depth with Doors Open 90°: 49". Depth with Drawer
Reviewed: 2026-09-04

rlpool WRMF3736SV 36 Inch Freestanding 4-Door ... Depth with Doors Open 90°: 49". Depth with Drawer Open: 55 11/16". Height To Top

Why this value was used

rlpool WRMF3736SV 36 Inch Freestanding 4-Door ... Depth with Doors Open 90°: 49". Depth with Drawer Open: 55 11/16". Height To Top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Whirlpool® 29 Cu. Ft. Family-Sized Capacity French Door ...
www.artnoeyappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact model specification table: Cutout Width 36.188 in; normalized to 36 3/16 in
Reviewed: 2026-09-04

Exact model specification table: Cutout Width 36.188 in; normalized to 36 3/16 in

Why this value was used

Exact model specification table: Cutout Width 36.188 in; normalized to 36 3/16 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3736SV

Confidence label: high.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern WRMF3736SV.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3736SV

Confidence label: high.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern WRMF3736SV.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3736SV

Confidence label: medium.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side and at the top

Why this value was used

1/2" space on each side and at the top Calculation or inference: documented DOE model pattern WRMF3736SV.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3736SV

Confidence label: medium.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

2" space behind

Why this value was used

2" space behind Calculation or inference: documented DOE model pattern WRMF3736SV.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Whirlpool WRMF3336SV

Confidence label: medium.

Primary evidence

Whirlpool WRMF3336SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRMF3336SV; original evidence: next to a fixed wall, leave a minimum space of 3.75"

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRMF3336SV; original evidence: next to a fixed wall, leave a minimum space of 3.75" Calculation or inference: exact 8-dimension chassis signature; source model Whirlpool WRMF3336SV.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.8125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

WRMF3736S* dimension G, Cabinet width: 35 13/16" (909 mm).

Why this value was used

WRMF3736S* dimension G, Cabinet width: 35 13/16" (909 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3736SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.