Measurement evidence for Whirlpool WRMF3536SW

Value used by ExactFit

35.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in = exact cabinet width G

Confidence label: medium.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Closed width follows exact cabinet width G = 35 13/16 in; prior value came from a different WRFF model page.

Why this value was used

Closed width follows exact cabinet width G = 35 13/16 in; prior value came from a different WRFF model page. Calculation or inference: width_doors_closed_in = exact cabinet width G.

Other evidence found

• 35.75 in — superseded

  https://www.canadianappliance.ca/product/Whirlpool_WRFF3536SW_French_Door_Refrigerator_Whirlpool_WRFF3536SW.html; location not retained. Model scope: not separately recorded. Raw value: Low-confidence same-appliance width mapping: width_doors_closed_in=35.75 in from case_width_in.. The final reviewed registry supersedes this earlier audit value. Closed width follows exact cabinet width G = 35 13/16 in; prior value came from a different WRFF model page.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

C* Height to top of cabinet -> 69" (1753 mm)

Why this value was used

C* Height to top of cabinet -> 69" (1753 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height of top of hinges (D) = 70-1/16 in.

Why this value was used

Height of top of hinges (D) = 70-1/16 in.

Other evidence found

• 70.06 in — superseded

  https://www.canadianappliance.ca/product/Whirlpool_WRFF3536SW_French_Door_Refrigerator_Whirlpool_WRFF3536SW.html; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Height = 70.06 in | 5.75 inches | | Width with Doors Closed | 35.75 inches | | Width to Remove Crisper | 63.69 inches | | Height | 70.06 inches | | Height to Top of Cabinet | 68.81 inches | | Height to Top of Door Hinge | 70.00 inches | | Depth | 36.75 inches | |. The final reviewed registry supersedes this earlier audit value. Height of top of hinges (D) = 70-1/16 in.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

F Depth without doors -> 297/8" (758.8 mm)

Why this value was used

F Depth without doors -> 297/8" (758.8 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

E Depth with doors -> 34 3/4" (882.3 mm)

Why this value was used

E Depth with doors -> 34 3/4" (882.3 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Exact-family dimension guide (WRMF3536S*, WRMF3736S*): depth with doors E = 34 3/4 in.

Why this value was used

Exact-family dimension guide (WRMF3536S*, WRMF3736S*): depth with doors E = 34 3/4 in.

Other evidence found

• 36.75 in — superseded

  https://www.canadianappliance.ca/product/Whirlpool_WRFF3536SW_French_Door_Refrigerator_Whirlpool_WRFF3536SW.html; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 36.75 in | inches | | Height to Top of Cabinet | 68.81 inches | | Height to Top of Door Hinge | 70.00 inches | | Depth | 36.75 inches | | Depth Closed Excluding Handles | 34.69 inches | | Depth Closed Including Handles | 36.75 inches | | Depth Excluding. The final reviewed registry supersedes this earlier audit value. Exact-family dimension guide (WRMF3536S*, WRMF3736S*): depth with doors E = 34 3/4 in.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

49 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

WRFF3536SW Whirlpool French Door Refrigerator 36 inch 30 cu. ft. Canada Parts - Sale! Best Price, Reviews and Specs
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: ches | | Depth Excluding Doors | 29.88 inches | | Depth with Door Open 90° | 49 inches | | Depth - D
Reviewed: 2026-09-04

ches | | Depth Excluding Doors | 29.88 inches | | Depth with Door Open 90° | 49 inches | | Depth - Drawer Open | 55.69 inches | | Approx

Why this value was used

ches | | Depth Excluding Doors | 29.88 inches | | Depth with Door Open 90° | 49 inches | | Depth - Drawer Open | 55.69 inches | | Approx

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.8125 + 2 * 0.5 = 36.8125

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact cabinet width 35.8125 in plus documented 0.5-in clearance on each side.

Why this value was used

Exact cabinet width 35.8125 in plus documented 0.5-in clearance on each side. Calculation or inference: 35.8125 + 2 * 0.5 = 36.8125.

Other evidence found

• 36.75 in — superseded

  https://www.canadianappliance.ca/product/Whirlpool_WRFF3536SW_French_Door_Refrigerator_Whirlpool_WRFF3536SW.html + 105603060.pdf; page 2. Model scope: not separately recorded. Raw value: Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.75 + 2 * 0.5 = 36.75 in. Side evidence: To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.. The final reviewed registry supersedes this earlier audit value. Exact cabinet width 35.8125 in plus documented 0.5-in clearance on each side.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783870-reva.pdf
Whirlpool · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 70.5625 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783870-reva.pdf
Whirlpool · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 31.875 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from WRMF3336SV

Confidence label: medium.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783870-reva.pdf
Whirlpool · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Whirlpool WRMF3336SV: top_clearance_in=0.5 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from WRMF3336SV

Confidence label: medium.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202506/dimension-guide-w11783870-reva.pdf
Whirlpool · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Whirlpool WRMF3336SV: rear_clearance_in=2.0 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Whirlpool WRMF3336SV

Confidence label: medium.

Primary evidence

Whirlpool WRMF3336SV Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRMF3336SV; original evidence: next to a fixed wall, leave a minimum space of 3.75"

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRMF3336SV; original evidence: next to a fixed wall, leave a minimum space of 3.75" Calculation or inference: exact 8-dimension chassis signature; source model Whirlpool WRMF3336SV.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.8125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Exact WRMF3536S*/WRMF3736S* guide labels cabinet width G = 35 13/16 in.

Why this value was used

Exact WRMF3536S*/WRMF3736S* guide labels cabinet width G = 35 13/16 in.

Other evidence found

• 35.75 in — superseded

  https://www.canadianappliance.ca/product/Whirlpool_WRFF3536SW_French_Door_Refrigerator_Whirlpool_WRFF3536SW.html; location not retained. Model scope: not separately recorded. Raw value: (Liters) | 837.11 L | | Width | 35.75 inches | | Cabinet Width | 35.75 inches | | Width with Doors Closed | 35.75 inches | | Wi. The final reviewed registry supersedes this earlier audit value. Exact WRMF3536S*/WRMF3736S* guide labels cabinet width G = 35 13/16 in.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRMF3536SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.