This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.5 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 65.6 in | ✓ Conflicting sources — resolved | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit65.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.6 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit66.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 27.7559 in | ✓ Verified — equivalent model · Calculated/inferred | Midea MRB19B5AST User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit27.7559 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared 750-mm Midea cabinet platform Confidence label: medium. Primary evidenceMidea MRB19B5AST User Manual Shared 30-in cabinet body depth; exact external width/depth/height agree.Open original source ↗ Why this value was usedShared 30-in cabinet body depth; exact external width/depth/height agree. Calculation or inference: shared 750-mm Midea cabinet platform. Why evidence from MRB19B5AST appliesTarget model: MRT18S3ABB. Supporting model: MRB19B5AST. Manufacturer: Midea. Product family and measurement relationship: shared 750-mm Midea cabinet platform. Measurement transferred: Depth without door. Relevant equivalence evidence: Shared 30-in cabinet body depth; exact external width/depth/height agree.. Known differences: not separately recorded. Review decision: documented inference; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.9 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit30.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 30.9 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit30.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 57.2559 in | ✓ Secondary source only · Calculated/inferred | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit57.2559 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 27.7559 + 29.5 Confidence label: medium. Primary evidenceMidea MRT18S3ABB User Manual Single-door 90-degree geometric envelope from cabinet depth and width.Open original source ↗ Why this value was usedSingle-door 90-degree geometric envelope from cabinet depth and width. Calculation or inference: 27.7559 + 29.5. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.5 in | ✓ Secondary source only · Calculated/inferred | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit35.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 * 3.0 Confidence label: medium. Primary evidenceMidea MRT18S3ABB User Manual Width plus documented 3-in clearance on each side.Open original source ↗ Why this value was usedWidth plus documented 3-in clearance on each side. Calculation or inference: 29.5 + 2 * 3.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.6 in | ✓ Secondary source only · Calculated/inferred | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit69.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceMidea MRT18S3ABB User Manual Minimum opening height derived from highest appliance endpoint 66.6 in plus documented top clearance 3.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest appliance endpoint 66.6 in plus documented top clearance 3.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.7559 in | ✓ Verified — equivalent model · Calculated/inferred | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 7 | |
Value used by ExactFit30.7559 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceMidea MRT18S3ABB User Manual Minimum opening depth is the verified cabinet depth plus the documented rear clearance.Open original source ↗ Why this value was usedMinimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Why evidence from MRB19B5AST appliesTarget model: MRT18S3ABB. Supporting model: MRB19B5AST. Manufacturer: Midea. Product family and measurement relationship: depth_case_only_in + rear_clearance_in. Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth is the verified cabinet depth plus the documented rear clearance.. Known differences: not separately recorded. Review decision: documented cavity formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 3 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Legacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 3 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Legacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3 in | ✓ Secondary source only · Calculated/inferred | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: declared_multi_model_scope Confidence label: medium. Primary evidenceMidea MRT18S3ABB User Manual 7.6 cm) Clearance at the topOpen original source ↗ Why this value was used7.6 cm) Clearance at the top Calculation or inference: cached document family mapping: declared_multi_model_scope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 3 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 7 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Manufacturer family manual specifies 3 in clearance at the top, rear, and sides.Open original source ↗ Why this value was usedManufacturer family manual specifies 3 in clearance at the top, rear, and sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 3 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 7 | |
Value used by ExactFit3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Manufacturer family manual specifies 3 in clearance at the top, rear, and sides.Open original source ↗ Why this value was usedManufacturer family manual specifies 3 in clearance at the top, rear, and sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.5 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 8 | |
Value used by ExactFit29.5 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 3 in | ✓ Secondary source only | Midea MRT18S3ABB User Manual assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea MRT18S3ABB User Manual Exact manual recommends 3 in at both sides.Open original source ↗ Why this value was usedExact manual recommends 3 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 65.6 in. Earlier retained values: 66 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitassets.skulytics.io · User Manual · secondary model/source
Model numbers covered: MRT18S3ABB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
16 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · User Manual · equivalent model/source
Model numbers covered: MRB19B5AST. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth without door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.