Measurement evidence for Midea MRB19B7AWW

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 29.5276 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 29.5 in — superseded

  https://www.midea.com/us/refrigerators/bottom-mount/bottom-mount-refrigerator-electronic-reversible-door.mrb19b7ast; location not retained. Model scope: not separately recorded. Raw value: Physical Specifications * Product Depth 30.9 in * Product Width 29.5 in * Product Height 66.6 in * Product Weight 185 lbs. The final reviewed registry supersedes this earlier audit value. Exact-model or explicitly covered Midea dimensional source.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 66.6142 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 66.6142 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 66.6 in — superseded

  https://www.midea.com/us/refrigerators/bottom-mount/bottom-mount-refrigerator-electronic-reversible-door.mrb19b7ast; location not retained. Model scope: not separately recorded. Raw value: * Product Depth 30.9 in * Product Width 29.5 in * Product Height 66.6 in * Product Weight 185 lbs Features * Capacity 18.7. The final reviewed registry supersedes this earlier audit value. Exact-model or explicitly covered Midea dimensional source.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 705 mm / 25.4

Confidence label: medium.

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Diagram endpoint C1 is the body envelope although the English table label is mistranslated.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 27.7559 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 30.9055 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 30.9055 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 30.9 in — superseded

  https://www.midea.com/us/refrigerators/bottom-mount/bottom-mount-refrigerator-electronic-reversible-door.mrb19b7ast; location not retained. Model scope: not separately recorded. Raw value: * Color Stainless Steel Physical Specifications * Product Depth 30.9 in * Product Width 29.5 in * Product Height 66.6 in . The final reviewed registry supersedes this earlier audit value. Exact-model or explicitly covered Midea dimensional source.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

58.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Midea MRB19B7AST 30 Inch Freestanding Bottom-Freezer ...
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model listing states Depth with Door Open 90 degrees = 58 3/8 in.
Reviewed: 2026-09-04

Cached exact-model listing states Depth with Door Open 90 degrees = 58 3/8 in.

Why this value was used

Cached exact-model listing states Depth with Door Open 90 degrees = 58 3/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 29.5276 + 2 * 3.937

Confidence label: medium.

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-04

Width plus documented >100 mm clearance on each side.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 37.4016 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Midea measurement source — saved-openparser:opj_zlWO3gS2ri3m_j742aDDP_0.json#cc4b0c01ab0751003e5e629c5bbb65c9
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 66.6142 in plus documented top clearance 3.0 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 69.6142 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Minimum opening depth is the verified cabinet depth plus the documented rear clearance.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 30.7559 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Manufacturer family material specifies 3 in clearance at the top, rear, and both sides.

Why this value was used

Manufacturer family material specifies 3 in clearance at the top, rear, and both sides. Calculation or inference: cached documented shared chassis propagation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Manufacturer family material specifies 3 in clearance at the top, rear, and both sides.

Why this value was used

Manufacturer family material specifies 3 in clearance at the top, rear, and both sides. Calculation or inference: cached documented shared chassis propagation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea measurement source — saved-openparser:opj_zlWO3gS2ri3m_j742aDDP_0.json#cc4b0c01ab0751003e5e629c5bbb65c9
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

7.6 cm) Clearance at the top

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

The retained record does not establish source scope or a resolvable supporting source.

Retained research value: 3 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Manufacturer family material specifies 3 in clearance at the top, rear, and both sides.

Why this value was used

Manufacturer family material specifies 3 in clearance at the top, rear, and both sides. Calculation or inference: cached documented shared chassis propagation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.937 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from MRB19B5AST

Confidence label: medium.

Primary evidence

Midea MRB19B5AST User Manual
assets.skulytics.io · User Manual
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Midea MRB19B5AST: hinge_side_wall_clearance_in=3.937 in.

Why this value was used

Conflict-free identical-chassis propagation from Midea MRB19B5AST: hinge_side_wall_clearance_in=3.937 in. Calculation or inference: identical 8-dimension chassis signature; propagated from MRB19B5AST.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 29.5276 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea MRB19B7AST User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 3.937 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.