This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
36-Inch Wide Side-by-Side Refrigerator with Exterior Ice and Water Dispenser - 25 Cu. Ft. Black MSS25C4MGB | Maytag Maytag
Retained specification excerpt: Sibling-chassis propagation from MSS25C4MGB, MSS25C4MGZ; model codes have the same numeric skeleton,
Value used by ExactFit
Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: same-chassis variant propagation from MSS25C4MGB, MSS25C4MGZ
Confidence label: high.
Primary evidence
36-Inch Wide Side-by-Side Refrigerator with Exterior Ice and Water Dispenser - 25 Cu. Ft. Black MSS25C4MGB | Maytag Maytag · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Sibling-chassis propagation from MSS25C4MGB, MSS25C4MGZ; model codes have the same numeric skeleton, Reviewed: 2026-09-04
Sibling-chassis propagation from MSS25C4MGB, MSS25C4MGZ; model codes have the same numeric skeleton, at least four existing chassis dimensions match, and no structural dimensions conflict. Sibling evidence: Depth Excluding Doors: 28.0 in | n Depth Closed Excluding Handles 31.625 in Depth Closed Including Handles 34 in Depth Excluding Doors 28 in Freezer Capacity Volume 9.07 cu. ft. Gross Weight 270 lbs Height 69.625 in Heig
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Retained research value: 28 in. It is preserved for audit but not accepted as a safe fit input.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Normal minimum cabinet cutout width: 36" (91.44 cm)
Normal minimum cabinet cutout width: 36" (91.44 cm)
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 69.25 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Maytag measurement source — https://www.maytag.com/content/dam/global/documents/201709/DimensionGuide-W11105301-D-MT.pdf Maytag · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05
Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in.
A required calculation input lacks defensible evidence.
Retained research value: 29 in. It is preserved for audit but not accepted as a safe fit input.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MSS25C4M****
Confidence label: medium.
Primary evidence
Maytag measurement source — https://www.maytag.com/content/dam/global/documents/201709/DimensionGuide-W11105301-D-MT.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05
1/2" of space on each side Calculation or inference: documented DOE model pattern MSS25C4M****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MSS25C4M****
Confidence label: medium.
Primary evidence
Maytag measurement source — https://www.maytag.com/content/dam/global/documents/201709/DimensionGuide-W11105301-D-MT.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05
1/2" of space on each side Calculation or inference: documented DOE model pattern MSS25C4M****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MSS25C4M****
Confidence label: medium.
Primary evidence
Maytag measurement source — https://www.maytag.com/content/dam/global/documents/201709/DimensionGuide-W11105301-D-MT.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05
1/2" of space on each side and at the top Calculation or inference: documented DOE model pattern MSS25C4M****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MSS25C4M****
Confidence label: medium.
Primary evidence
Maytag measurement source — https://www.maytag.com/content/dam/global/documents/201709/DimensionGuide-W11105301-D-MT.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05
1" of space behind Calculation or inference: documented DOE model pattern MSS25C4M****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
next to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: declared_multi_model_scope.
Why evidence from MSS25C4MGB applies
Target model: MSS25C4MGW. Supporting model: MSS25C4MGB. Manufacturer: Maytag. Product family and measurement relationship: cached document family mapping: declared_multi_model_scope.
Measurement transferred: Hinge-side wall clearance. Relevant equivalence evidence: next to a fixed wall, leave a 2" (5.08 cm. Known differences: not separately recorded. Review decision: local cached pdf native text; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag MSS25C4MGW Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Not found for safe fit use. Sources retained: https://www.maytag.com/kitchen/refrigerators/side-by-side/p.36-inch-wide-side-by-side-refrigerator-with-exterior-ice-and-water-dispenser-25-cu.-ft.mss25c4mgb.html. Related-model record: MSS25C4MGW.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Minimum cutout depth
Not found for safe fit use. Sources retained: https://www.maytag.com/content/dam/global/documents/201709/DimensionGuide-W11105301-D-MT.pdf. Related-model record: MSS25C4MGW.
A required calculation input lacks defensible evidence.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Model numbers covered: MSS25C4MGW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.