Measurement evidence for Maytag MRTX5119SW

Value used by ExactFit

29.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Aligned with case_width_in (29.5")

Why this value was used

Aligned with case_width_in (29.5")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.437 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to top of cabinet 1662.1 mm (657/16")

Why this value was used

Height to top of cabinet 1662.1 mm (657/16")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.189 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Height 1681.2 mm (663/16")

Why this value was used

Overall Height 1681.2 mm (663/16")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

E Cabinet Depth only 720 mm (283/8")

Why this value was used

E Cabinet Depth only 720 mm (283/8")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

30-Inch Wide Top-Freezer Refrigerator with Garage Mode—19 Cu. Ft. White MRTX5119SW | Maytag
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Closed Excluding Handles: 32.25 in | cation Freezer Compartment Types of Ice No ### Dimensions
Reviewed: 2026-09-04

Depth Closed Excluding Handles: 32.25 in | cation Freezer Compartment Types of Ice No ### Dimensions Cabinet Width 29.5 in Depth Closed Excluding Handles 32.25 in Depth Closed Including Handles 34.438 in Depth Excluding Doors 28.375 in Depth

Why this value was used

Depth Closed Excluding Handles: 32.25 in | cation Freezer Compartment Types of Ice No ### Dimensions Cabinet Width 29.5 in Depth Closed Excluding Handles 32.25 in Depth Closed Including Handles 34.438 in Depth Excluding Doors 28.375 in Depth

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.437 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Depth 874.7 mm (347/16")

Why this value was used

Overall Depth 874.7 mm (347/16")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

59.874 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with door open 90° 1520.8 mm (597/8")

Why this value was used

Depth with door open 90° 1520.8 mm (597/8")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 * 0.5

Confidence label: medium.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Minimum opening derived from exact product width plus explicit symmetric side spacing: 29.5 + 2 * 0.5 = 30.5 in. Side evidence: allow 1/2" (1.25 cm) of space on each side

Why this value was used

Minimum opening derived from exact product width plus explicit symmetric side spacing: 29.5 + 2 * 0.5 = 30.5 in. Side evidence: allow 1/2" (1.25 cm) of space on each side Calculation or inference: 29.5 + 2 * 0.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.689 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool WRTX7419SB Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 66.189 in plus propagated top clearance 1.5 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 66.189 in plus propagated top clearance 1.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool WRTX7419SB Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 28.375 in plus propagated rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 28.375 in plus propagated rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRTX5119S***

Confidence label: medium.

Primary evidence

Maytag measurement source — https://www.maytag.com/content/dam/global/documents/202508/dimension-guide-w11656231-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern MRTX5119S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRTX5119S***

Confidence label: medium.

Primary evidence

Maytag measurement source — https://www.maytag.com/content/dam/global/documents/202508/dimension-guide-w11656231-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern MRTX5119S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Whirlpool WRTX7419SB

Confidence label: medium.

Primary evidence

Whirlpool WRTX7419SB Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRTX7419SB; original evidence: Whirlpool installation manual explicit clearance: top_clearance_in=1.5 in. To ensure proper ventilation for your refrigerator, allow 1/2" (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1"

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRTX7419SB; original evidence: Whirlpool installation manual explicit clearance: top_clearance_in=1.5 in. To ensure proper ventilation for your refrigerator, allow 1/2" (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" Calculation or inference: exact 8-dimension chassis signature; source model Whirlpool WRTX7419SB.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Whirlpool WRTX7419SB

Confidence label: medium.

Primary evidence

Whirlpool WRTX7419SB Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRTX7419SB; original evidence: Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Whirlpool WRTX7419SB; original evidence: Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your Calculation or inference: exact 8-dimension chassis signature; source model Whirlpool WRTX7419SB.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Maytag top-mount door-swing architecture

Confidence label: medium.

Primary evidence

Maytag measurement source — https://www.maytag.com/content/dam/global/documents/202605/dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Documented Maytag top-mount platform: when next to a fixed wall, leave 2" minimum between refrigerator and wall for door swing.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.5 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of cabinet 749.3 mm (291/2")

Why this value was used

Width of cabinet 749.3 mm (291/2")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag MRTX5119SW Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

allow 1/2" (1.25 cm) of space on each side

Why this value was used

allow 1/2" (1.25 cm) of space on each side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.