Measurement evidence for LG LF25H6330D

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to LG LF25H6330D fit check Check this model against your opening How ExactFit verifies measurements

LG LF25H6330D

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

7exact-model manufacturer values

0verified equivalent/same-chassis values

9secondary-source-only values

0values with unresolved source details

Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	32.9375 in	✓ Conflicting sources — resolved	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 32.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width 32 15/16 in Open original source ↗ Why this value was used Width 32 15/16 in Other evidence found 35.125 in — superseded 104687243.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35 1/8" x 71 7/16" x 37 5/8". The final reviewed registry supersedes this earlier audit value. Width 32 15/16 in Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.625 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height to Top of Case 68 5/8 Open original source ↗ Why this value was used Height to Top of Case 68 5/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.9375 in	✓ Conflicting sources — resolved	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 69.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height Top of Hinge or Door Cap 69 15/16 in Open original source ↗ Why this value was used Height Top of Hinge or Door Cap 69 15/16 in Other evidence found 71.4375 in — superseded 104687243.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35 1/8" x 71 7/16" x 37 5/8". The final reviewed registry supersedes this earlier audit value. Height Top of Hinge or Door Cap 69 15/16 in Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	29.5 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth without Door 29 1/2" Open original source ↗ Why this value was used Depth without Door 29 1/2" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	33.4375 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 33.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth without Handles 33 7/16" Open original source ↗ Why this value was used Depth without Handles 33 7/16" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	35.9375 in	✓ Conflicting sources — resolved	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 35.9375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth with Handles 35 15/16 in Open original source ↗ Why this value was used Depth with Handles 35 15/16 in Other evidence found 37.625 in — superseded 104687243.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35 1/8" x 71 7/16" x 37 5/8". The final reviewed registry supersedes this earlier audit value. Depth with Handles 35 15/16 in Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	46.6875 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 46.6875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth (Total with Door Open) 46 11/16" Open original source ↗ Why this value was used Depth (Total with Door Open) 46 11/16" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	33.1875 in	✓ Verified — exact model · Calculated/inferred	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Retained specification excerpt: Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 *
Value used by ExactFit 33.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_clearance_wall_in = 33.1875 Confidence label: high. Calculation inputs: Overall width; Adjoining-wall clearance (reviewed endpoint); Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 * Reviewed: 2026-09-04 Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 33.1875 in Open original source ↗ Why this value was used Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 33.1875 in Calculation or inference: width_doors_closed_in + 2 * side_clearance_wall_in = 33.1875. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.9375 in	✓ Secondary source only · Calculated/inferred	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 70.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence LG LF25H6330D None assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Minimum opening height derived from highest stored appliance endpoint 69.9375 in plus documented top clearance 1.0 in. Open original source ↗ Why this value was used Minimum opening height derived from highest stored appliance endpoint 69.9375 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	31.5 in	✓ Secondary source only · Calculated/inferred	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence LG LF25H6330D None assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 LG opening envelope: 29.5 + 2.0 = 31.5 in. Open original source ↗ Why this value was used LG opening envelope: 29.5 + 2.0 = 31.5 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.125 in	✓ Verified — exact model	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Installation Clearance: Sides 1/8 in Open original source ↗ Why this value was used Installation Clearance: Sides 1/8 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.125 in	✓ Verified — exact model	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Installation Clearance: Sides 1/8 in Open original source ↗ Why this value was used Installation Clearance: Sides 1/8 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	1 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Installation Clearance \| Sides 1/8", Top 1", Back 2" \| Carton Dimensions (WxHxD) Open original source ↗ Why this value was used Installation Clearance \| Sides 1/8", Top 1", Back 2" \| Carton Dimensions (WxHxD) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Specification sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Installation Clearance Sides 1/8", Top 1", Back 2" Open original source ↗ Why this value was used Installation Clearance Sides 1/8", Top 1", Back 2" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	4.75 in	✓ Secondary source only	LG LF25H6330D None assets.skulytics.io	Page 1
Value used by ExactFit 4.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG LF25H6330D None assets.skulytics.io · Specification sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Door Edge Clearance with Handle 4 3/4" Open original source ↗ Why this value was used Door Edge Clearance with Handle 4 3/4" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	32.9375 in	✓ Conflicting sources — resolved	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 32.9375 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width 32 15/16 in; sheet applies to LF25H6330D and LF25H6330S Open original source ↗ Why this value was used Width 32 15/16 in; sheet applies to LF25H6330D and LF25H6330S Other evidence found 35.125 in — superseded 104687243.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35 1/8" x 71 7/16" x 37 5/8". The final reviewed registry supersedes this earlier audit value. Width 32 15/16 in; sheet applies to LF25H6330D and LF25H6330S Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	0.125 in	✓ Conflicting sources — resolved	LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG	Page 1
Value used by ExactFit 0.125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Installation Clearance: Sides 1/8 in Open original source ↗ Why this value was used Installation Clearance: Sides 1/8 in Other evidence found 4.75 in — superseded 104687243.pdf; page 1. Model scope: not separately recorded. Raw value: Door Edge Clearance with Handle 4 3/4". The final reviewed registry supersedes this earlier audit value. Installation Clearance: Sides 1/8 in Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Overall width

Selected: 32.9375 in. Earlier retained values: 35.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Width 32 15/16 in

View source scope, location, and impact on fit

Height with hinge / controlling height

Selected: 69.9375 in. Earlier retained values: 71.4375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Height Top of Hinge or Door Cap 69 15/16 in

View source scope, location, and impact on fit

Depth with handle

Selected: 35.9375 in. Earlier retained values: 37.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth with Handles 35 15/16 in

View source scope, location, and impact on fit

Cabinet case width

Selected: 32.9375 in. Earlier retained values: 35.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Width 32 15/16 in; sheet applies to LF25H6330D and LF25H6330S

View source scope, location, and impact on fit

Adjoining-wall clearance (reviewed endpoint)

Selected: 0.125 in. Earlier retained values: 4.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Installation Clearance: Sides 1/8 in

View source scope, location, and impact on fit

Source documents and pages

LG measurement source — https://www.lg.com/us/support/products/documents/LF25H6330SD_2024_Refrigeration_Spec_Sheet.pdf

LG · Web source · exact model/source

Model numbers covered: LF25H6330D. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

8 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with handle; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

LG LF25H6330D None

assets.skulytics.io · Specification sheet · secondary model/source

Model numbers covered: LF25H6330D. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

9 displayed measurements supported: Cabinet height; Depth without door; Depth with door, without handles; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Hinge-side wall clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether LF25H6330D fits your opening Back to LG LF25H6330D Read the full verification methodology

Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.

Evidence summary

Complete mixed evidence

Measurements and supporting evidence

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence