This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
24 Cu. Ft. 36-Inch Counter-Depth French Door Refrigerator with Internal Water Dispenser in Juniper Juniper KRFC236SJP | KitchenAid KitchenAid
Retained specification excerpt: Depth With Door Open 90 Degree 44.25 in
Value used by ExactFit
44.25 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24 Cu. Ft. 36-Inch Counter-Depth French Door Refrigerator with Internal Water Dispenser in Juniper Juniper KRFC236SJP | KitchenAid KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door Open 90 Degree 44.25 in Reviewed: 2026-09-04
24 Cu. Ft. 36-Inch Counter-Depth French Door Refrigerator with Internal Water Dispenser in Juniper Juniper KRFC236SJP | KitchenAid KitchenAid
Retained specification excerpt: Cutout Width = 36.0 in | 5F FC 30F/45F RC ### Dimensions Cabinet Width 35.625 in Cutout Height 70.12
Value used by ExactFit
36 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24 Cu. Ft. 36-Inch Counter-Depth French Door Refrigerator with Internal Water Dispenser in Juniper Juniper KRFC236SJP | KitchenAid KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Width = 36.0 in | 5F FC 30F/45F RC ### Dimensions Cabinet Width 35.625 in Cutout Height 70.12 Reviewed: 2026-09-04
Cutout Width = 36.0 in | 5F FC 30F/45F RC ### Dimensions Cabinet Width 35.625 in Cutout Height 70.125 in Cutout Width 36 in Depth Closed Excluding Handles 29.438 in Depth Closed Including Handles 32.125
Cutout Width = 36.0 in | 5F FC 30F/45F RC ### Dimensions Cabinet Width 35.625 in Cutout Height 70.125 in Cutout Width 36 in Depth Closed Excluding Handles 29.438 in Depth Closed Including Handles 32.125
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 69.9375 in plus documented top clearance 0.25 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFC236S****
Confidence label: medium.
Primary evidence
KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202505/dimension-guide-w11776311-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
3/16" space on each side Calculation or inference: documented DOE model pattern KRFC236S****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFC236S****
Confidence label: medium.
Primary evidence
KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202505/dimension-guide-w11776311-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
3/16" space on each side Calculation or inference: documented DOE model pattern KRFC236S****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFC236S****
Confidence label: medium.
Primary evidence
KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202505/dimension-guide-w11776311-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
3/16" space on each side and 1/4" space at the top
3/16" space on each side and 1/4" space at the top Calculation or inference: documented DOE model pattern KRFC236S****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFC236S****
Confidence label: medium.
Primary evidence
KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202505/dimension-guide-w11776311-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1" space behind Calculation or inference: documented DOE model pattern KRFC236S****.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
KitchenAid KRFC236SBE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
next to a fixed wall, leave a 33/4" (9.5 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Why evidence from KRFC236SBE applies
Target model: KRFC236SJP. Supporting model: KRFC236SBE. Manufacturer: KitchenAid. Product family and measurement relationship: cached document family mapping: generic_or_unscoped_shared_document.
Measurement transferred: Hinge-side wall clearance. Relevant equivalence evidence: next to a fixed wall, leave a 33/4" (9.5 cm. Known differences: not separately recorded. Review decision: local cached pdf native text; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid KRFC236SJP Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04
Model numbers covered: KRFC236SJP. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.