This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 7 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 47.1875 in | ✓ Secondary source only | KitchenAid KBSN748SJP Fit System Limited Guarantee assets.skulytics.io | Page 1 | |
Value used by ExactFit47.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Fit System Limited Guarantee Overall Width -> 473∕16" (1199 mm)Open original source ↗ Why this value was usedOverall Width -> 473∕16" (1199 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | Unknown | ? Not found | KitchenAid KBSN748SPS Dimension Guide assets.skulytics.io | Page 4 | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SPS Dimension Guide Visual side-view table: Cabinet Height = 74 3/8 in.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 74.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.25 in | ✓ Secondary source only | KitchenAid KBSN748SJP Fit System Limited Guarantee assets.skulytics.io | Page 1 | |
Value used by ExactFit83.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Fit System Limited Guarantee Overall Height -> 831∕4" (2115 mm)Open original source ↗ Why this value was usedOverall Height -> 831∕4" (2115 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | Unknown | ? Not found · Calculated/inferred | 29.4 Cu. Ft. 48-Inch Built-In Side-by-Side Refrigerator with Signature Platinum Interior in PrintShield® Finish Stainless Steel with PrintShield™ Finish KBSN748SPS | KitchenAid KitchenAid | Retained specification excerpt: strict_chassis_consensus: Consensus from KBSN748SPS | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Consensus from KBSN748SPS Confidence label: high. Primary evidence29.4 Cu. Ft. 48-Inch Built-In Side-by-Side Refrigerator with Signature Platinum Interior in PrintShield® Finish Stainless Steel with PrintShield™ Finish KBSN748SPS | KitchenAid strict_chassis_consensus: Consensus from KBSN748SPSOpen original source ↗ Why this value was usedA low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 22.4 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 25.8125 in | ✓ Secondary source only | KitchenAid KBSN748SJP Fit System Limited Guarantee assets.skulytics.io | Page 1 | |
Value used by ExactFit25.8125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Fit System Limited Guarantee Depth without Handle -> 2513∕16" (655 mm)Open original source ↗ Why this value was usedDepth without Handle -> 2513∕16" (655 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.8125 in | ✓ Secondary source only | KitchenAid KBSN748SJP Fit System Limited Guarantee assets.skulytics.io | Page 1 | |
Value used by ExactFit27.8125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Fit System Limited Guarantee Depth with Handle -> 2713∕16" (706 mm)Open original source ↗ Why this value was usedDepth with Handle -> 2713∕16" (706 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | Unknown | ? Not found · Calculated/inferred | 29.4 Cu. Ft. 48-Inch Built-In Side-by-Side Refrigerator with Signature Platinum Interior in PrintShield® Finish Stainless Steel with PrintShield™ Finish KBSN748SPS | KitchenAid KitchenAid | Retained specification excerpt: strict_chassis_consensus: Consensus from KBSN748SPS | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Consensus from KBSN748SPS Confidence label: high. Primary evidence29.4 Cu. Ft. 48-Inch Built-In Side-by-Side Refrigerator with Signature Platinum Interior in PrintShield® Finish Stainless Steel with PrintShield™ Finish KBSN748SPS | KitchenAid strict_chassis_consensus: Consensus from KBSN748SPSOpen original source ↗ Why this value was usedA low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 50.69 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 49.25 in | ✓ Secondary source only | KitchenAid KBSN748SJP Dimension Guide assets.skulytics.io | Page 7 | |
Value used by ExactFit49.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Dimension Guide Model Total Opening Width (W) Width Between Cleats (X) -> 48" 491/4" to 491/2" (1251 mm to 1257 mm) 471/2" to 473/4" (1207 mm to 1213 mm)Open original source ↗ Why this value was usedModel Total Opening Width (W) Width Between Cleats (X) -> 48" 491/4" to 491/2" (1251 mm to 1257 mm) 471/2" to 473/4" (1207 mm to 1213 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 83.5 in | ✓ Secondary source only | KitchenAid KBSN748SJP 48 Inch Built-In Side-by-Side Refrigerator with 30 cu. ft. Total Capacity, Automatic Ice Maker, Signature Platinum Interior, Preserva® Cooling System, Ultra-Bright LED Lighting, Touchscreen Controls, Max Cool, Sabbath Mode and Star-K Certified: Juniper www.ajmadison.com | Retained specification excerpt: Cutout Height: 83 1/2 In | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceKitchenAid KBSN748SJP 48 Inch Built-In Side-by-Side Refrigerator with 30 cu. ft. Total Capacity, Automatic Ice Maker, Signature Platinum Interior, Preserva® Cooling System, Ultra-Bright LED Lighting, Touchscreen Controls, Max Cool, Sabbath Mode and Star-K Certified: Juniper Cutout Height: 83 1/2 InOpen original source ↗ Why this value was usedCutout Height: 83 1/2 In Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Secondary source only | KitchenAid KBSN748SJP 48 Inch Built-In Side-by-Side Refrigerator with 30 cu. ft. Total Capacity, Automatic Ice Maker, Signature Platinum Interior, Preserva® Cooling System, Ultra-Bright LED Lighting, Touchscreen Controls, Max Cool, Sabbath Mode and Star-K Certified: Juniper www.ajmadison.com | Retained specification excerpt: Cutout Depth: 25 In | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceKitchenAid KBSN748SJP 48 Inch Built-In Side-by-Side Refrigerator with 30 cu. ft. Total Capacity, Automatic Ice Maker, Signature Platinum Interior, Preserva® Cooling System, Ultra-Bright LED Lighting, Touchscreen Controls, Max Cool, Sabbath Mode and Star-K Certified: Juniper Cutout Depth: 25 InOpen original source ↗ Why this value was usedCutout Depth: 25 In Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | Unknown | ? Not found | KitchenAid measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.1875 in per-side installation clearance from dominant manufacturer-family specification p | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — local-cache manufacturer-family consensus Inferred 0.1875 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.188 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | Unknown | ? Not found | KitchenAid measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.1875 in per-side installation clearance from dominant manufacturer-family specification p | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — local-cache manufacturer-family consensus Inferred 0.1875 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.188 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.75 in | ✓ Secondary source only | KitchenAid KBSN748SJP Dimension Guide assets.skulytics.io | Page 6 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Dimension Guide Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille.Open original source ↗ Why this value was usedExact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | Unknown | ? Not found · Calculated/inferred | KitchenAid KBSN748SJP 48 Inch Built-In Side-by-Side Refrigerator with 30 cu. ft. Total Capacity, Automatic Ice Maker, Signature Platinum Interior, Preserva® Cooling System, Ultra-Bright LED Lighting, Touchscreen Controls, Max Cool, Sabbath Mode and Star-K Certified: Juniper www.ajmadison.com | Retained specification excerpt: KitchenAid built-in opening residual: 25.0 - 22.4 = 2.6 in behind the case within the accepted openi | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: medium. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceKitchenAid KBSN748SJP 48 Inch Built-In Side-by-Side Refrigerator with 30 cu. ft. Total Capacity, Automatic Ice Maker, Signature Platinum Interior, Preserva® Cooling System, Ultra-Bright LED Lighting, Touchscreen Controls, Max Cool, Sabbath Mode and Star-K Certified: Juniper KitchenAid built-in opening residual: 25.0 - 22.4 = 2.6 in behind the case within the accepted opening.Open original source ↗ Why this value was usedA required calculation input lacks defensible evidence. Retained research value: 2.6 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found · Calculated/inferred | KitchenAid KBSN748TPA Installation Instruction assets.skulytics.io | Page 7 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: full-size KitchenAid built-in hinge platform minimum Confidence label: medium. Primary evidenceKitchenAid KBSN748TPA Installation Instruction KitchenAid built-in door-swing guide: allow 4 1/2" minimum between the refrigerator side and a corner wall; more may be needed for custom panels or extended handles.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 4.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 47.1875 in | ✓ Secondary source only | KitchenAid KBSN748SJP Fit System Limited Guarantee assets.skulytics.io | Page 1 | |
Value used by ExactFit47.1875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid KBSN748SJP Fit System Limited Guarantee Overall Width -> 473∕16" (1199 mm)Open original source ↗ Why this value was usedOverall Width -> 473∕16" (1199 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | Unknown | ? Not found · Calculated/inferred | KitchenAid measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.1875 in per-side installation clearance from dominant manufacturer-family specification p | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Popular-brand chassis/type consensus: Tall built-in family side clearance Confidence label: low. Primary evidenceKitchenAid measurement source — local-cache manufacturer-family consensus Inferred 0.1875 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedA low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.1875 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: Unknown. Earlier retained values: 83.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 106162515.pdf. Related-model record: KBSN748SPS.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: https://www.kitchenaid.com/major-appliances/refrigeration/built-in-refrigerators/built-in-side-by-side/p.pdpv5.KBSN748SPS.html. Related-model record: KBSN748SJP.
A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: https://www.kitchenaid.com/major-appliances/refrigeration/built-in-refrigerators/built-in-side-by-side/p.pdpv5.KBSN748SPS.html. Related-model record: KBSN748SJP.
A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: https://www.ajmadison.com/cgi-bin/ajmadison/KBSN748SJP.html. Related-model record: KBSN748SJP.
A required calculation input lacks defensible evidence.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 106162839.pdf. Related-model record: KBSN748TPA.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Fit System Limited Guarantee · secondary model/source
Model numbers covered: KBSN748SJP. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
5 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Dimension Guide · Scope not established
Model numbers covered: KBSN748SPS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Cabinet height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗KitchenAid · Web source · Scope not established
Model numbers covered: KBSN748SJP. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Depth without door; Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Dimension Guide · secondary model/source
Model numbers covered: KBSN748SJP. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout width; Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.ajmadison.com · Web source · Scope not established
Model numbers covered: KBSN748SJP. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
3 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
3 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL unavailable in the record.
assets.skulytics.io · Installation Instruction · Scope not established
Model numbers covered: KBSN748TPA. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Hinge-side wall clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.