Measurement evidence for Kenmore A125007830

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Kenmore A125007830 fit check Check this model against your opening How ExactFit verifies measurements

Kenmore A125007830

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Incomplete evidence

8exact-model manufacturer values

4verified equivalent/same-chassis values

0secondary-source-only values

4values with unresolved source details

Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	29.72 in	✓ Verified — exact model	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official Kenmore structured product specification.
Value used by ExactFit 29.72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official Kenmore structured product specification. Reviewed: 2026-09-04 Official Kenmore structured product specification. Open original source ↗ Why this value was used Official Kenmore structured product specification. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.35 in	✓ Verified — exact model	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official Kenmore structured product specification.
Value used by ExactFit 68.35 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official Kenmore structured product specification. Reviewed: 2026-09-04 Official Kenmore structured product specification. Open original source ↗ Why this value was used Official Kenmore structured product specification. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	68.78 in	✓ Conflicting sources — resolved	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official Kenmore structured product specification.
Value used by ExactFit 68.78 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official Kenmore structured product specification. Reviewed: 2026-09-04 Official Kenmore structured product specification. Open original source ↗ Why this value was used Official Kenmore structured product specification. Other evidence found 90 in — superseded https://myeliteappliances.com/refrigeration/refrigerators/top-freezer-refrigerators/a125007830; location not retained. Model scope: not separately recorded. Raw value: height to top of hinge (in.) : Depth w/ Door Open 90 Degrees . The final reviewed registry supersedes this earlier audit value. Official Kenmore structured product specification. Open alternative source ↗ Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	28.35 in	✓ Verified — exact model	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official Kenmore structured product specification.
Value used by ExactFit 28.35 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official Kenmore structured product specification. Reviewed: 2026-09-04 Official Kenmore structured product specification. Open original source ↗ Why this value was used Official Kenmore structured product specification. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	31.69 in	✓ Verified — exact model	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official Kenmore structured product specification.
Value used by ExactFit 31.69 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official Kenmore structured product specification. Reviewed: 2026-09-04 Official Kenmore structured product specification. Open original source ↗ Why this value was used Official Kenmore structured product specification. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	31.69 in	✓ Verified — exact model	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official Kenmore structured product specification.
Value used by ExactFit 31.69 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official Kenmore structured product specification. Reviewed: 2026-09-04 Official Kenmore structured product specification. Open original source ↗ Why this value was used Official Kenmore structured product specification. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	62.41 in	✓ Verified — exact model · Calculated/inferred	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: Official payload contains zero; inferred from the exact predecessor Kenmore 30-in top-freezer door-e
Value used by ExactFit 62.41 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 31.69 + 29.72 + 1.0 predecessor door-envelope allowance Confidence label: medium. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official payload contains zero; inferred from the exact predecessor Kenmore 30-in top-freezer door-e Reviewed: 2026-09-04 Official payload contains zero; inferred from the exact predecessor Kenmore 30-in top-freezer door-envelope pattern. Open original source ↗ Why this value was used Official payload contains zero; inferred from the exact predecessor Kenmore 30-in top-freezer door-envelope pattern. Calculation or inference: 31.69 + 29.72 + 1.0 predecessor door-envelope allowance. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	Unknown	? Not found · Calculated/inferred	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.72 + 2 * 3.2 Confidence label: medium. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Not established Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-04 Exact width plus the manual's required clearance on both sides. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 36.12 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	71.98 in	✓ Verified — equivalent model · Calculated/inferred	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit 71.98 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Open original source ↗ Why this value was used Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Why evidence from A125007636 applies Target model: A125007830. Supporting model: A125007636. Manufacturer: Kenmore. Product family and measurement relationship: max(height_case_in,height_hinge_in) + top_clearance_in. Measurement transferred: Minimum cutout height. Relevant equivalence evidence: Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.. Known differences: not separately recorded. Review decision: documented cavity formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	31.55 in	✓ Verified — equivalent model · Calculated/inferred	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit 31.55 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Open original source ↗ Why this value was used Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Why evidence from A125007636 applies Target model: A125007830. Supporting model: A125007636. Manufacturer: Kenmore. Product family and measurement relationship: depth_case_only_in + rear_clearance_in. Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth is the verified cabinet depth plus the documented rear clearance.. Known differences: not separately recorded. Review decision: documented cavity formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	Unknown	? Not found	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Endpoint migration from reviewed side_clearance_wall_in; evidence explicitly states each/both sides Confidence label: high. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Not established Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Stored reviewed evidence explicitly applies the clearance to each/both sides. Manual requires 3.2 in on each side and on the hinge side at a fixed wall. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 3.2 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	Unknown	? Not found	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Endpoint migration from reviewed side_clearance_wall_in; evidence explicitly states each/both sides Confidence label: high. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Not established Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Stored reviewed evidence explicitly applies the clearance to each/both sides. Manual requires 3.2 in on each side and on the hinge side at a fixed wall. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 3.2 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	3.2 in	✓ Verified — equivalent model · Calculated/inferred	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit 3.2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides. Open original source ↗ Why this value was used Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides. Calculation or inference: cached documented shared chassis propagation. Why evidence from A125007636 applies Target model: A125007830. Supporting model: A125007636. Manufacturer: Kenmore. Product family and measurement relationship: Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides.. Measurement transferred: Top clearance. Relevant equivalence evidence: Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides.. Known differences: not separately recorded. Review decision: cached documented shared chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	3.2 in	✓ Verified — equivalent model · Calculated/inferred	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit 3.2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides. Open original source ↗ Why this value was used Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides. Calculation or inference: cached documented shared chassis propagation. Why evidence from A125007636 applies Target model: A125007830. Supporting model: A125007636. Manufacturer: Kenmore. Product family and measurement relationship: Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides.. Measurement transferred: Rear clearance. Relevant equivalence evidence: Manufacturer family manual specifies 3.2 in installation clearance on all surrounding sides.. Known differences: not separately recorded. Review decision: cached documented shared chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	Unknown	? Not found	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Not established Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-05 Manual requires 3.2 in on each side and on the hinge side at a fixed wall. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 3.2 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	29.72 in	✓ Verified — exact model · Calculated/inferred	Kenmore measurement source — new202.html Kenmore	Retained specification excerpt: No side projections; standardized case width to official closed-door width.
Value used by ExactFit 29.72 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case width = exact closed-door width Confidence label: medium. Primary evidence Kenmore measurement source — new202.html Kenmore · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: No side projections; standardized case width to official closed-door width. Reviewed: 2026-09-04 No side projections; standardized case width to official closed-door width. Open original source ↗ Why this value was used No side projections; standardized case width to official closed-door width. Calculation or inference: case width = exact closed-door width. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	Unknown	? Not found	Kenmore A125007636 User Manual assets.skulytics.io	Page 11
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Kenmore A125007636 User Manual assets.skulytics.io · User Manual Model scope: Not established Publication/revision date: Not recorded Location: Page 11 Reviewed: 2026-09-04 Manual requires 3.2 in on each side and on the hinge side at a fixed wall. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 3.2 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Height with hinge / controlling height

Selected: 68.78 in. Earlier retained values: 90 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Official Kenmore structured product specification.

View source scope, location, and impact on fit