This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 23.6 in | ✓ Conflicting sources — resolved | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit23.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 58 in | ✓ Verified — exact model | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit58 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 59.4 in | ✓ Verified — exact model | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit59.4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 22 in | ✓ Conflicting sources — resolved | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit22 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 25 in | ✓ Verified — exact model | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 25.3 in | ✓ Verified — exact model | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit25.3 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 47 in | ✓ Conflicting sources — resolved | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit47 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 25.6 in | ✓ Verified — exact model · Calculated/inferred | Haier HA10TG21SW Use and Care Manual Haier | Retained specification excerpt: Official overall width plus the documented minimum side air clearance on both sides. | |
Value used by ExactFit25.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 23.6 + 2 * 1.0 Confidence label: medium. Primary evidenceHaier HA10TG21SW Use and Care Manual Official overall width plus the documented minimum side air clearance on both sides.Open original source ↗ Why this value was usedOfficial overall width plus the documented minimum side air clearance on both sides. Calculation or inference: 23.6 + 2 * 1.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 60.4 in | ✓ Secondary source only · Calculated/inferred | Haier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf images.salsify.com | Page 2 | |
Value used by ExactFit60.4 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceHaier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf Minimum opening height derived from highest stored appliance endpoint 59.4 in plus documented top clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 59.4 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Secondary source only · Calculated/inferred | Haier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf images.salsify.com | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceHaier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf Minimum opening depth derived from case-only depth 22.0 in plus documented rear clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 22.0 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 1 in | ✓ Secondary source only | Haier HA10TG21SW Use and Care Manual assets.skulytics.io | Page 10 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceHaier HA10TG21SW Use and Care Manual Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 1 in | ✓ Secondary source only | Haier HA10TG21SW Use and Care Manual assets.skulytics.io | Page 10 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceHaier HA10TG21SW Use and Care Manual Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Secondary source only · Calculated/inferred | Haier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf images.salsify.com | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern HA10TG21**** Confidence label: high. Primary evidenceHaier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf clearances top 1"Open original source ↗ Why this value was usedclearances top 1" Calculation or inference: documented DOE model pattern HA10TG21****. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Secondary source only · Calculated/inferred | Haier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf images.salsify.com | Page 2 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern HA10TG21**** Confidence label: high. Primary evidenceHaier measurement source — https://images.salsify.com/image/upload/s--Jkry-Q37--/fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf clearances top 1" back 2"Open original source ↗ Why this value was usedclearances top 1" back 2" Calculation or inference: documented DOE model pattern HA10TG21****. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 1 in | ✓ Secondary source only | Haier HA10TG21SW Use and Care Manual assets.skulytics.io | Page 10 | |
Value used by ExactFit1 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier HA10TG21SW Use and Care Manual Manufacturer guide specifies 1 in side clearance and a 90-degree zero-radius reversible door; no larger fixed-wall minimum is stated.Open original source ↗ Why this value was usedManufacturer guide specifies 1 in side clearance and a 90-degree zero-radius reversible door; no larger fixed-wall minimum is stated. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 23.6 in | ✓ Conflicting sources — resolved · Calculated/inferred | 9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW Haier | Retained specification excerpt: No wider case projection is documented; standardized case width to official overall width. | |
Value used by ExactFit23.6 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case width = official overall width Confidence label: medium. Primary evidence9.8 Cu. Ft. Top Freezer Refrigerator - HA10TG21SW No wider case projection is documented; standardized case width to official overall width.Open original source ↗ Why this value was usedNo wider case projection is documented; standardized case width to official overall width. Calculation or inference: case width = official overall width. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 1 in | ✓ Secondary source only | Haier HA10TG21SW Use and Care Manual assets.skulytics.io | Page 10 | |
Value used by ExactFit1 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier HA10TG21SW Use and Care Manual Installation manual specifies 1 inch minimum clearance at each side.Open original source ↗ Why this value was usedInstallation manual specifies 1 inch minimum clearance at each side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 23.6 in. Earlier retained values: 23.4 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current exact-model Haier official weights and dimensions specification.
View source scope, location, and impact on fitSelected: 22 in. Earlier retained values: 22.4 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current exact-model Haier official weights and dimensions specification.
View source scope, location, and impact on fitSelected: 47 in. Earlier retained values: 46.9 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current exact-model Haier official weights and dimensions specification.
View source scope, location, and impact on fitSelected: 23.6 in. Earlier retained values: 23.4 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
No wider case projection is documented; standardized case width to official overall width. Calculation or inference: case width = official overall width.
View source scope, location, and impact on fitHaier · Web source · exact model/source
Model numbers covered: HA10TG21SW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Haier · Use and Care Manual · exact model/source
Model numbers covered: HA10TG21SW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗images.salsify.com · Web source · secondary model/source
Model numbers covered: HA10TG21SW. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Use and Care Manual · secondary model/source
Model numbers covered: HA10TG21SW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.