Measurement evidence for GE GTS18GTNRWW

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to GE GTS18GTNRWW fit check Check this model against your opening How ExactFit verifies measurements

GE GTS18GTNRWW

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Incomplete evidence

0exact-model manufacturer values

1verified equivalent/same-chassis values

13secondary-source-only values

2values with unresolved source details

Last reviewed: 2026-09-05. 5 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	28 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 28 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width (in.) G -> 28 Open original source ↗ Why this value was used Width (in.) G -> 28 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	66.875 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 66.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height to top of case (in.) B -> 66-7/8 Open original source ↗ Why this value was used Height to top of case (in.) B -> 66-7/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	67.375 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 67.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height to top of hinge (in.) A -> 67-3/8 Open original source ↗ Why this value was used Height to top of hinge (in.) A -> 67-3/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	26.75 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 26.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Case depth without door (in.) C -> 26-3/4 Open original source ↗ Why this value was used Case depth without door (in.) C -> 26-3/4 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	30.5 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 30.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Case depth less door handle (in.) D -> 30-1/2 Open original source ↗ Why this value was used Case depth less door handle (in.) D -> 30-1/2 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	32.625 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 32.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Case depth with door handle (in.) E -> 32-5/8 Open original source ↗ Why this value was used Case depth with door handle (in.) E -> 32-5/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	57 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 57 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth with fresh food door open 90˚ (in.) F -> 57 Open original source ↗ Why this value was used Depth with fresh food door open 90˚ (in.) F -> 57 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	29.5 in	✓ Secondary source only · Calculated/inferred	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 29.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 28.0 + 2 * 0.75 Confidence label: medium. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Minimum opening derived from exact product width plus explicit symmetric side spacing: 28.0 + 2 * 0.75 = 29.5 in. Side evidence: Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 67-3/8 \| 66-7/8 \| 26-3/4 \| 30-1/2 \| 32-5/8 \| 57 \| 28 \| 30-5/8 \| 3/4 \| 1 \| 2 Open original source ↗ Why this value was used Minimum opening derived from exact product width plus explicit symmetric side spacing: 28.0 + 2 * 0.75 = 29.5 in. Side evidence: Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 67-3/8 \| 66-7/8 \| 26-3/4 \| 30-1/2 \| 32-5/8 \| 57 \| 28 \| 30-5/8 \| 3/4 \| 1 \| 2 Calculation or inference: 28.0 + 2 * 0.75. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	68.375 in	✓ Secondary source only · Calculated/inferred	GE® 17.5 Cu. Ft. Top-Freezer Refrigerator handhwarehouse.com	Retained specification excerpt: Minimum opening height = highest verified appliance height 67.375 in + GE top clearance 1 in.
Value used by ExactFit 68.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence GE® 17.5 Cu. Ft. Top-Freezer Refrigerator handhwarehouse.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening height = highest verified appliance height 67.375 in + GE top clearance 1 in. Reviewed: 2026-09-05 Minimum opening height = highest verified appliance height 67.375 in + GE top clearance 1 in. Open original source ↗ Why this value was used Minimum opening height = highest verified appliance height 67.375 in + GE top clearance 1 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	Unknown	? Not found · Calculated/inferred	GE GTS18GTNRWW Top Freezer Refrigerators rthomesolutionsllc.com	Retained specification excerpt: Minimum opening depth = verified case-only depth 26.75 in + GE rear clearance 2 in.
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence GE GTS18GTNRWW Top Freezer Refrigerators rthomesolutionsllc.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening depth = verified case-only depth 26.75 in + GE rear clearance 2 in. Reviewed: 2026-09-05 Minimum opening depth = verified case-only depth 26.75 in + GE rear clearance 2 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 28.75 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.75 in	✓ Verified — equivalent model · Calculated/inferred	GE GIE18DTNRBB Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 0.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from GIE18DTNRBB Confidence label: medium. Primary evidence GE GIE18DTNRBB Quick Specs assets.skulytics.io · Quick Specs Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Conflict-free identical-chassis propagation from GE GIE18DTNRBB: side_ventilation_clearance_in=0.75 in. Open original source ↗ Why this value was used Conflict-free identical-chassis propagation from GE GIE18DTNRBB: side_ventilation_clearance_in=0.75 in. Calculation or inference: identical 8-dimension chassis signature; propagated from GIE18DTNRBB. Why evidence from GIE18DTNRBB applies Target model: GTS18GTNRWW. Supporting model: GIE18DTNRBB. Manufacturer: GE. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from GIE18DTNRBB. Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from GE GIE18DTNRBB: side_ventilation_clearance_in=0.75 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.75 in	✓ Verified — equivalent model · Calculated/inferred	GE GIE18DTNRBB Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 0.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from GIE18DTNRBB Confidence label: medium. Primary evidence GE GIE18DTNRBB Quick Specs assets.skulytics.io · Quick Specs Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Conflict-free identical-chassis propagation from GE GIE18DTNRBB: side_ventilation_clearance_in=0.75 in. Open original source ↗ Why this value was used Conflict-free identical-chassis propagation from GE GIE18DTNRBB: side_ventilation_clearance_in=0.75 in. Calculation or inference: identical 8-dimension chassis signature; propagated from GIE18DTNRBB. Why evidence from GIE18DTNRBB applies Target model: GTS18GTNRWW. Supporting model: GIE18DTNRBB. Manufacturer: GE. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from GIE18DTNRBB. Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from GE GIE18DTNRBB: side_ventilation_clearance_in=0.75 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	1 in	✓ Secondary source only	GE® 17.5 Cu. Ft. Top-Freezer Refrigerator handhwarehouse.com	Retained specification excerpt: Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary p
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence GE® 17.5 Cu. Ft. Top-Freezer Refrigerator handhwarehouse.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary p Reviewed: 2026-09-05 Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary parsed value. Open original source ↗ Why this value was used Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary parsed value. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	Unknown	? Not found	GE GTS18GTNRWW Top Freezer Refrigerators rthomesolutionsllc.com	Retained specification excerpt: Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 dom
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Top Freezer Refrigerators rthomesolutionsllc.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 dom Reviewed: 2026-09-05 Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 domains; official=False. Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	2.625 in	✓ Secondary source only · Calculated/inferred	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 2.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: ceil_to_1/8(width_open_90 - max(case_width,width_closed)) Confidence label: medium. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Exact-model GE width-open geometry: width with door(s) open 90 degrees 30.625 in; widest closed appliance width 28 in; single-door side excess rounded upward to 1/8 in = 2.625 in. Table: 67-3/8 \| 66-7/8 \| 26-3/4 \| 30-1/2 \| 32-5/8 \| 57 \| 28 \| 30-5/8 \| 3/4 \| 1 \| 2 Open original source ↗ Why this value was used Exact-model GE width-open geometry: width with door(s) open 90 degrees 30.625 in; widest closed appliance width 28 in; single-door side excess rounded upward to 1/8 in = 2.625 in. Table: 67-3/8 \| 66-7/8 \| 26-3/4 \| 30-1/2 \| 32-5/8 \| 57 \| 28 \| 30-5/8 \| 3/4 \| 1 \| 2 Calculation or inference: ceil_to_1/8(width_open_90 - max(case_width,width_closed)). Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	28 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 28 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width (in.) G -> 28 Open original source ↗ Why this value was used Width (in.) G -> 28 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	0.75 in	✓ Secondary source only	GE GTS18GTNRWW Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 0.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE GTS18GTNRWW Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 67-3/8 \| 66-7/8 \| 26-3/4 \| 30-1/2 \| 32-5/8 \| 57 \| 28 \| 30-5/8 \| 3/4 \| 1 \| 2 Open original source ↗ Why this value was used Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 67-3/8 \| 66-7/8 \| 26-3/4 \| 30-1/2 \| 32-5/8 \| 57 \| 28 \| 30-5/8 \| 3/4 \| 1 \| 2 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Measurements not established

Minimum cutout depth

Not found for safe fit use. Sources retained: https://rthomesolutionsllc.com/refrigeration/refrigerators/top-freezer-refrigerators/gts18gtnrww. Related-model record: GTS18GTNRWW.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Rear clearance

Not found for safe fit use. Sources retained: https://rthomesolutionsllc.com/refrigeration/refrigerators/top-freezer-refrigerators/gts18gtnrww. Related-model record: GTS18GTNRWW.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Source documents and pages

GE GTS18GTNRWW Quick Specs

assets.skulytics.io · Quick Specs · secondary model/source

Model numbers covered: GTS18GTNRWW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).