This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 5 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 30 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Width 30"Open original source ↗ Why this value was usedWidth 30" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 65.875 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit65.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Height Without Hinge 65 7/8"Open original source ↗ Why this value was usedHeight Without Hinge 65 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.375 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit66.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Height With Hinge 66 3/8"Open original source ↗ Why this value was usedHeight With Hinge 66 3/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 28.25 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit28.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Depth of Cabinet 28 1/4"Open original source ↗ Why this value was usedDepth of Cabinet 28 1/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 32 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit32 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Depth With Door 32"Open original source ↗ Why this value was usedDepth With Door 32" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 32 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit32 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Depth With Door and Handle 32"Open original source ↗ Why this value was usedDepth With Door and Handle 32" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 58.625 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit58.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Depth With Door 90° Open 58 5/8"Open original source ↗ Why this value was usedDepth With Door 90° Open 58 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | Unknown | ? Not found · Calculated/inferred | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Retained specification excerpt: Derived minimum opening width 30.75 in from product width 30.0 in and explicit 0.375 in clearance on | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 30.0 + 2 * 0.375 Confidence label: medium. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Derived minimum opening width 30.75 in from product width 30.0 in and explicit 0.375 in clearance on each side.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 30.75 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 66.75 in | ✓ Secondary source only · Calculated/inferred | Frigidaire FFHT2045XB Complete Owner's Guide assets.skulytics.io | Page 8 | |
Value used by ExactFit66.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceFrigidaire FFHT2045XB Complete Owner's Guide Minimum opening height derived from highest stored appliance endpoint 66.375 in plus documented top clearance 0.375 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 66.375 in plus documented top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 29.25 in | ✓ Verified — equivalent model · Calculated/inferred | Frigidaire FFHT2022AB Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit29.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceFrigidaire FFHT2022AB Installation Instructions Minimum opening depth derived from case-only depth 28.25 in plus documented rear clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 28.25 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Why evidence from FFHT2022AB appliesTarget model: FFHT2045XB. Supporting model: FFHT2022AB. Manufacturer: Frigidaire. Product family and measurement relationship: depth_case_only_in + rear_clearance_in. Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth derived from case-only depth 28.25 in plus documented rear clearance 1.0 in.. Known differences: not separately recorded. Review decision: calculated formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | Unknown | ? Not found | Frigidaire measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — local-cache manufacturer-family consensus Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | Unknown | ? Not found | Frigidaire measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — local-cache manufacturer-family consensus Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Secondary source only | Frigidaire FFHT2045XB Complete Owner's Guide assets.skulytics.io | Page 8 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceFrigidaire FFHT2045XB Complete Owner's Guide • | Sides and top 3/8" (9.5 mm) | •Open original source ↗ Why this value was used• | Sides and top 3/8" (9.5 mm) | • Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — equivalent model · Calculated/inferred | Frigidaire FFHT2022AB Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from FFHT2022AB Confidence label: medium. Primary evidenceFrigidaire FFHT2022AB Installation Instructions Conflict-free identical-chassis propagation from Frigidaire FFHT2022AB: rear_clearance_in=1.0 in.Open original source ↗ Why this value was usedConflict-free identical-chassis propagation from Frigidaire FFHT2022AB: rear_clearance_in=1.0 in. Calculation or inference: identical 8-dimension chassis signature; propagated from FFHT2022AB. Why evidence from FFHT2022AB appliesTarget model: FFHT2045XB. Supporting model: FFHT2022AB. Manufacturer: Frigidaire. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from FFHT2022AB. Measurement transferred: Rear clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from Frigidaire FFHT2022AB: rear_clearance_in=1.0 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found · Calculated/inferred | Frigidaire measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: hinge-side baseline = documented side ventilation clearance Confidence label: medium. Primary evidenceFrigidaire measurement source — local-cache manufacturer-family consensus Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern. Hinge-side wall note is conditional and gives no separate numeric minimum; this value is the documented side-clearance baseline. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedA low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 30 in | ✓ Secondary source only | Frigidaire FFHT2045XB Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit30 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2045XB Product Specifications Sheet Width of Cabinet 30"Open original source ↗ Why this value was usedWidth of Cabinet 30" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | Unknown | ? Not found · Calculated/inferred | Frigidaire measurement source — local-cache manufacturer-family consensus Publisher not recorded | Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Popular-brand chassis/type consensus: Strong modal installation clearance for this manufacturer family Confidence label: low. Primary evidenceFrigidaire measurement source — local-cache manufacturer-family consensus Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedA low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: 104457249.pdf + local-cache manufacturer-family consensus. Related-model record: FFHT2045XB.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: local-cache manufacturer-family consensus. No rejected related-model candidate is identified in the retained record.
A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Product Specifications Sheet · secondary model/source
Model numbers covered: FFHT2045XB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product Specifications Sheet · Scope not established
Model numbers covered: FFHT2045XB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Complete Owner's Guide · secondary model/source
Model numbers covered: FFHT2045XB. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout height; Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation Instructions · equivalent model/source
Model numbers covered: FFHT2022AB. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.