Measurement evidence for Bosch B36FD52SNB

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Bosch B36FD52SNB fit check Check this model against your opening How ExactFit verifies measurements

Bosch B36FD52SNB

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Incomplete evidence

0exact-model manufacturer values

1verified equivalent/same-chassis values

8secondary-source-only values

7values with unresolved source details

Last reviewed: 2026-09-05. 5 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	36 in	✓ Secondary source only	Bosch B36FD52SNB None assets.skulytics.io	Page 1
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 HxWxD) (inches) 70" x 36" x 25" Open original source ↗ Why this value was used HxWxD) (inches) 70" x 36" x 25" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	69.5 in	✓ Conflicting sources — resolved	Bosch B36FD52SNB None assets.skulytics.io	Page 1
Value used by ExactFit 69.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint Open original source ↗ Why this value was used exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint Other evidence found 70 in — superseded 102943542.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value. exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	70 in	✓ Secondary source only	Bosch B36FD52SNB None assets.skulytics.io	Page 1
Value used by ExactFit 70 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 HxWxD) (inches) 70" x 36" x 25" Open original source ↗ Why this value was used HxWxD) (inches) 70" x 36" x 25" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	Unknown	? Not found · Calculated/inferred	Bosch measurement source — Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com Publisher not recorded	Retained specification excerpt: B36FD52 specification: Overall depth without doors and handles 29 5/16 in.
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: matching B36FD52 finish-family chassis propagation Confidence label: medium. Primary evidence Bosch measurement source — Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: B36FD52 specification: Overall depth without doors and handles 29 5/16 in. Reviewed: 2026-09-04 B36FD52 specification: Overall depth without doors and handles 29 5/16 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 29.3125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	Unknown	? Not found · Calculated/inferred	Bosch measurement source — Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com Publisher not recorded	Retained specification excerpt: Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 exact listing/specification a
Value used by ExactFit Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: matching B36FD52 finish-family chassis propagation Confidence label: medium. Primary evidence Bosch measurement source — Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 exact listing/specification a Reviewed: 2026-09-04 Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 exact listing/specification alignment: handleless depth 32 1/8 in; replaces 25-inch cutout depth. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 32.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 25 in — superseded 102943542.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value. Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 exact listing/specification alignment: handleless depth 32 1/8 in; replaces 25-inch cutout depth. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	Unknown	? Not found · Calculated/inferred	Bosch measurement source — Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com Publisher not recorded	Retained specification excerpt: Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 specification: Overall depth
Value used by ExactFit Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: matching B36FD52 finish-family chassis propagation Confidence label: medium. Primary evidence Bosch measurement source — Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 specification: Overall depth Reviewed: 2026-09-04 Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 specification: Overall depth with doors and handles 35 7/16 in; replaces 25-inch cutout depth. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 35.4375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 25 in — superseded 102943542.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value. Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 specification: Overall depth with doors and handles 35 7/16 in; replaces 25-inch cutout depth. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	47.75 in	✓ Verified — equivalent model · Calculated/inferred	Bosch 500 Series 36 in. 26 cu. ft. Smart Standard Depth ... www.homedepot.com	Retained specification excerpt: Bosch B36FD52SNS cached matching-chassis specification
Value used by ExactFit 47.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Bosch B36FD52SNS cached matching-chassis specification Confidence label: medium. Primary evidence Bosch 500 Series 36 in. 26 cu. ft. Smart Standard Depth ... www.homedepot.com · Web source Model scope: Equivalent model Publication/revision date: Not recorded Location: Retained specification excerpt: Bosch B36FD52SNS cached matching-chassis specification Reviewed: 2026-09-04 Bosch B36FD52SNS cached matching-chassis specification Open original source ↗ Why this value was used Bosch B36FD52SNS cached matching-chassis specification Calculation or inference: Bosch B36FD52SNS cached matching-chassis specification. Why evidence from B36FD52SNS applies Target model: B36FD52SNB. Supporting model: B36FD52SNS. Manufacturer: Bosch. Product family and measurement relationship: Bosch B36FD52SNS cached matching-chassis specification. Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: Bosch B36FD52SNS cached matching-chassis specification. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	Unknown	? Not found · Calculated/inferred	Bosch B36FD52SNB None assets.skulytics.io	Retained specification excerpt: Derived minimum opening width 36.25 in from product width 36.0 in and explicit 0.125 in clearance on
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 36.0 + 2 * 0.125 Confidence label: medium. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Derived minimum opening width 36.25 in from product width 36.0 in and explicit 0.125 in clearance on Reviewed: 2026-09-04 Derived minimum opening width 36.25 in from product width 36.0 in and explicit 0.125 in clearance on each side. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 36.25 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.5 in	✓ Secondary source only · Calculated/inferred	Bosch B36FD52SNB None assets.skulytics.io	Page 2
Value used by ExactFit 70.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: medium. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 70 in overall height plus documented 1/2 in top ventilation = 70 1/2 in opening. Open original source ↗ Why this value was used 70 in overall height plus documented 1/2 in top ventilation = 70 1/2 in opening. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	Unknown	? Not found · Calculated/inferred	Bosch B36FD52SNB None assets.skulytics.io	Page 2
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Installation envelope is cabinet depth plus the documented 1 in rear ventilation gap. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 30.3125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	Unknown	? Not found	Bosch measurement source — local-cache manufacturer-family consensus Publisher not recorded	Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch measurement source — local-cache manufacturer-family consensus Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa Reviewed: 2026-09-05 Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used The retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	Unknown	? Not found	Bosch measurement source — local-cache manufacturer-family consensus Publisher not recorded	Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch measurement source — local-cache manufacturer-family consensus Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa Reviewed: 2026-09-05 Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used The retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.5 in	✓ Secondary source only	Bosch B36FD52SNB None assets.skulytics.io	Page 2
Value used by ExactFit 0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Open original source ↗ Why this value was used Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	1 in	✓ Secondary source only	Bosch B36FD52SNB None assets.skulytics.io	Page 2
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Exact Bosch manual: leave 1 in behind for proper ventilation. Open original source ↗ Why this value was used Exact Bosch manual: leave 1 in behind for proper ventilation. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	0.125 in	✓ Secondary source only · Calculated/inferred	Bosch B36FD52SNB None assets.skulytics.io	Page 1
Value used by ExactFit 0.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: hinge wall baseline = documented side spacing Confidence label: medium. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Bosch diagram documents 1/8 in side spacing; no separate larger numeric wall offset is stated, so this is the controlling baseline. Open original source ↗ Why this value was used Bosch diagram documents 1/8 in side spacing; no separate larger numeric wall offset is stated, so this is the controlling baseline. Calculation or inference: hinge wall baseline = documented side spacing. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	36 in	✓ Secondary source only	Bosch B36FD52SNB None assets.skulytics.io	Page 1
Value used by ExactFit 36 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Bosch B36FD52SNB None assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 HxWxD) (inches) 70" x 36" x 25" Open original source ↗ Why this value was used HxWxD) (inches) 70" x 36" x 25" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	Unknown	? Not found · Calculated/inferred	Bosch measurement source — local-cache manufacturer-family consensus Publisher not recorded	Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa
Value used by ExactFit Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Popular-brand chassis/type consensus: Strong modal installation clearance for this manufacturer family Confidence label: low. Primary evidence Bosch measurement source — local-cache manufacturer-family consensus Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa Reviewed: 2026-09-04 Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pattern. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 69.5 in. Earlier retained values: 70 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

View source scope, location, and impact on fit

Depth with door, without handles

Selected: Unknown. Earlier retained values: 25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.